I need a Arduino with Z-Wave controller prototype

  • Durum: Closed
  • Ödül: $50
  • Alınan Girdiler: 1

Yarışma Özeti

prize goes to those with the best solutions and the ability to deliver more in 1000 the devices over time.

Hello. I need a prototype of Arduino with Z-Wave chip. (Gateway)

The prototype must have these FUNCTIONS
- Z-Wave support as skla have contact with a z-wave module. That will send data (numerical values) back to Arduino
- Arduino must have Ethernet port
- Arduino shall transmit data on to a server through Ethernet port.
I wish that this will be delivered fairly quickly so therefore one can very well use some finished products and assembled.

Prototype to be sent to me in Norway
Programming with my z-wave module must be done in Norway over the internet

One requirement is the gateway is tested against a z-wave unitary before passing it to me ..
If the prototype works well so we need next time 500 pieces.

winner of the competition is awarded the contract.
Give therefore appreciate their prototype.

Tavsiye Edilen Beceriler

Bu yarışmadan başlıca girdiler

Daha Fazla Katılım Görüntüle

Genel Açıklama Panosu

  • GabrielSoare
    GabrielSoare
    • 2 yıl önce

    Hi, you are talking about the arduino with z-wave protocol, then move to Raspberry PI usb stick.
    If I understood well, your need actually is to be able to send ? or fetch data from lots of sensors to that Zwave stick? it's not so clear for me.

    • 2 yıl önce
    1. GabrielSoare
      GabrielSoare
      • 2 yıl önce

      I have multiple components which are based on Z-wave and a z-wave stick which can be attached to rasberry. If you can explain what do you really want to achieve maybe I can do it, for real, not just to apply with an arduino picture.
      Btw, my Z-wave components are produced by aeon labs> aeotec .

      • 2 yıl önce
    2. larryluu
      Yarışma Sahibi
      • 2 yıl önce

      i ned low cost gatewaye support z-wave i not need app, website etc..

      • 2 yıl önce
  • infozebros
    infozebros
    • 3 yıl önce

    Hi Can i use my own gateway, instead of Z Wave Frequency, it should be same as Z Wave Freq. (both specifications are same)...

    • 3 yıl önce
    1. larryluu
      Yarışma Sahibi
      • 2 yıl önce

      ok?

      • 2 yıl önce
    2. larryluu
      Yarışma Sahibi
      • 2 yıl önce

      Great if you can see in the pdf on your gw can talk to my unit.

      • 2 yıl önce
  • larryluu
    Yarışma Sahibi
    • 3 yıl önce

    http://www.ebay.com/itm/Wireless-module-with-wires-Arduino-compatible-Z-wave-frequency-/140772604858?hash=item20c6b37bba can ass add with on my Ardino

    • 3 yıl önce
    1. thegoodhen
      thegoodhen
      • 3 yıl önce

      In the item description it says "Note: this module works on Z-wave frequency, but not on Z-wave protocol."

      But you need to communicate with other devices that use the same protocol, right? Also, sorry, I am not sure what your question is.

      • 3 yıl önce
  • larryluu
    Yarışma Sahibi
    • 3 yıl önce

    Or if you run RaZberry Pi UZB interface

    • 3 yıl önce
  • larryluu
    Yarışma Sahibi
    • 3 yıl önce

    Yes directly or with an option card

    • 3 yıl önce
    1. thegoodhen
      thegoodhen
      • 3 yıl önce

      Okay, thank you for clarifying!

      • 3 yıl önce
    2. larryluu
      Yarışma Sahibi
      • 3 yıl önce

      please come with a proposal

      • 3 yıl önce
  • thegoodhen
    thegoodhen
    • 3 yıl önce

    Hello! If I understand it correctly, you want Arduino board with ethernet and also z-wave directly on the printed circuit board. Is that correct?

    • 3 yıl önce

Daha fazla yorum göster

Yarışmalara nasıl başlanır

  • Projenizi ilan edin

    Yarışmanızı İlan Edin Hızlı ve kolay

  • Tonlarca girdi alın

    Tonlarca Girdi Alın Bütün dünyadan

  • En iyi girdiyi seçin

    En iyi girdiyi seçin Dosyaları indirin - Kolay!

Şimdi bir Yarışma İlan Et ya da Bugün Bize Katılın!