Prototyping infrared micro power receiving block.

  • Durum: Closed
  • Ödül: €100
  • Alınan Girdiler: 8
  • Kazanan: sbarbarelli

Yarışma Özeti

The block has to be able to transform infrared radiation, around 940 nm, to electrical output of 3-4 V, 40 mW or more.
Requirements:
Block circuit is self-powered from the abovementioned infrared energy source (without additional battery, etc).
Block has to be restricted to size less than 1 square cm, and less than 2-3 mm height.
Block components have to be common/accessible/inexpensive, preferably of SMD type.
Possible solution is "Joule thief" schema with PIN Photodiode. However, other solutions are welcomed.
Project's result has to be presented as EasyEDA compatible schematic and PCB, with video proof of its functioning.

Aranan Beceriler

İşveren Geribildirimi

“Santiago demonstrates the best knowledge and problem understanding among all participants! Also he is very pleasant and easy person for communication. ”

Profil Görüntüsü shatil9, Ukraine.

Bu yarışmadan başlıca girdiler

Daha Fazla Girdi Görüntüleyin

Genel Açıklama Panosu

  • dev904536
    dev904536
    • 4 ay önce

    i am work seriously

    • 4 ay önce
    1. shatil9
      Yarışma Sahibi
      • 4 ay önce

      Please, show me what have you done

      • 4 ay önce
  • dev904536
    dev904536
    • 4 ay önce

    hello i almost complete your project but you rejected me dear.

    • 4 ay önce
  • sbarbarelli
    sbarbarelli
    • 5 ay önce

    Hi! good project! very interesting...
    I have a question...the complete block can measure up to 1cmX1cm base by 3mm height? including julius thief?
    I am working on the problem..
    Thanks..

    • 5 ay önce
    1. sbarbarelli
      sbarbarelli
      • 4 ay önce

      Hi again!
      I am working on this project. I have already managed to make (and measure) a prototype of a very small "julius thief" that delivers the requested power; unfortunately I still do not get the pin diode components that I consider most appropriate.
      I have a question... do you need the 40mw continuously (as long as there is infrared radiation of course) or do you only need them periodically? Thanks!

      • 4 ay önce
    2. shatil9
      Yarışma Sahibi
      • 4 ay önce

      Hi, Santiago, and sorry for delay with answer. Freelancer doesn't notify about posts... Uninterruptible power source is preferable, but if you achieve good efficiency, interruptions will be acceptable too. If you are asking about longevity of block working, it will work during periods in order of several hours

      • 4 ay önce
  • EngDarwishelectr
    EngDarwishelectr
    • 5 ay önce

    what is the kind of Transmitter(Transmitter IC or module )? it can be remote control mobile device just mention the transmitter module to get the ic number

    • 5 ay önce
    1. shatil9
      Yarışma Sahibi
      • 5 ay önce

      No, it shouldn't, but it is acceptable too

      • 5 ay önce
    2. shatil9
      Yarışma Sahibi
      • 5 ay önce

      I have updated project description: "Block circuit is self-powered from the abovementioned infrared energy source (without additional battery, etc)." Please, revise your circuit. Also a LED (D1), what is it for? I don't need it. Is it for load simulation or for indication purpose?

      • 5 ay önce
  • shatil9
    Yarışma Sahibi
    • 5 ay önce

    I have updated project description: "Block circuit is self-powered from the abovementioned infrared energy source (without additional battery, etc)." It seemed obvious for me, but I have to admit that it is not obvious for others...

    • 5 ay önce

Daha fazla yorum göster

Yarışmalara nasıl başlanır

  • Projenizi ilan edin

    Yarışmanızı İlan Edin Hızlı ve kolay

  • Tonlarca girdi alın

    Tonlarca Girdi Alın Bütün dünyadan

  • En iyi girdiyi seçin

    En iyi girdiyi seçin Dosyaları indirin - Kolay!

Şimdi bir Yarışma İlan Et ya da Bugün Bize Katılın!