Simple 3D model of a tray

  • Durum: Closed
  • Ödül: $20
  • Alınan Girdiler: 32
  • Kazanan: VKarmaa

Yarışma Özeti

Hello-
I'm looking for a simple 3D model of a tray built from the attached rough drawings. Please review the attached PDF - it has the necessary dimensions and details. Some notes below:

1) The tray should be 11" long x 3 1/4" wide
2) The thickness of the tray and all the walls should be 2.5MM thick
3) There should be 3 channels in the bottom of the tray (created by 2 walls along the bottom of the tray
4) The tray should be 2" high
5) The front of the tray is open (no front wall)
6) All corners of the tray should have a slight rounding (no sharp corners)
7) The pattern of the tray throughout (walls, floor, etc.) should be small honeycomb (not solid walls). Example: [login to view URL]
8) The final file needs to be a 3d printable file, and it will need to be in 2 parts (6" long max). The 2 parts will need to snap together easily to form 1 full piece.

THANK YOU in advance

Tavsiye Edilen Beceriler

Genel Açıklama Panosu

  • charlstonsmallsc
    Yarışma Sahibi
    • 1 ay önce

    I want to sincerely thank all of you for your entries on this project. You all submitted amazing work - it was a very difficult decision to narrow to just one design. Thank you all very much!

    • 1 ay önce
  • khurrummah85
    khurrummah85
    • 1 ay önce

    Can you tell the 3D Printer type because the design of the tray depends upon the technique of Printing. Is it FDM, SLS, SLA ? Because some designs need support structures too but some don't

    • 1 ay önce
    1. tejaspetkar2
      tejaspetkar2
      • 1 ay önce

      SLA,

      • 1 ay önce
  • ahmedkasse
    ahmedkasse
    • 1 ay önce

    hi sir i'm working on the tray and i jyst want to know where you want the tray to sepreate and join

    • 1 ay önce
    1. charlstonsmallsc
      Yarışma Sahibi
      • 1 ay önce

      Length-wise. I can only print 6", so by cutting the 11" length in half, that will work. Hope that makes sense.

      • 1 ay önce
  • mahipalbasera3
    mahipalbasera3
    • 1 ay önce

    #24

    • 1 ay önce
  • charlstonsmallsc
    Yarışma Sahibi
    • 1 ay önce

    Thank you all for your submissions so far. Just to explain my star rating:
    3 stars = good
    4 stars = very good

    Every submission is appreciated so far!

    • 1 ay önce
  • DC47
    DC47
    • 1 ay önce

    Dont Close the contest Early.

    • 1 ay önce
  • jaypang
    jaypang
    • 1 ay önce

    Could you elaborate on "channel wall is sloped at the front" please? It's the only part of your sketch which is slightly ambiguous. Thanks

    • 1 ay önce
  • VKarmaa
    VKarmaa
    • 1 ay önce

    working on it. If possible please #increaseprize

    • 1 ay önce
    1. VKarmaa
      VKarmaa
      • 1 ay önce

      Also, please tell the purpose/use of the tray

      • 1 ay önce

Daha fazla yorum göster

Yarışmalara nasıl başlanır

  • Projenizi ilan edin

    Yarışmanızı İlan Edin Hızlı ve kolay

  • Tonlarca girdi alın

    Tonlarca Girdi Alın Bütün dünyadan

  • En iyi girdiyi seçin

    En iyi girdiyi seçin Dosyaları indirin - Kolay!

Şimdi bir Yarışma İlan Et ya da Bugün Bize Katılın!