İşe Almak için Schematics Power Engineers

  • Schematics
  • Power Converters
Öneriler:
daha fazla

Ülkeler

Belirli Konum

Sınavlar

Saatlik Ücret (USD)

Derecelendirme

Çevrimiçi

  • trutony adlı kullanıcıyı işe alın
    3.0
    1 değerlendirme saatlik $30 USD
    Control engineering & Power Electronics Expert, abundant experience in practical design and development of embedded systems. I controlled step motor, dc motor and different valves etc. with Motorola, Intel and PIC microcontrollers. I developed control system for ship engine and realized communication over CAN bus...
    Control engineering & Power Electronics Expert, abundant experience in practical design and development of embedded systems. I controlled step motor, dc motor and different valves etc. with Motorola, Intel and PIC microcontrollers. I developed control system for ship engine and realized communication over CAN bus between different control devices. I developed High speed and High torque control system for IPMSM(Interior Permanent Magnet Synchronous Motor). I have applied drive of LED, LCD and PWM etc. using all peripheral like GPIO, timers, UART, SPI, I2C and others of S3C2440- application processor for eLinux. -Matlab and Mathematics -Control Engineering -Power Electronics -Electrical Engineering -PLC & SCADA -Microcontroller -Embedded Software -Software Development -Algorithm -Artificial Intelligence(GA, IA, NN, Fuzzy Logic, PSO etc.) -C & C++ Programming -Python -Electronics -Wireless daha az
  • horaciodrut adlı kullanıcıyı işe alın
    3.0
    1 değerlendirme saatlik $40 USD
    Passionate for electronics, I enjoy working with microcontrollers, FPGAs, Arduino, Rpi. I can also custom design your power supply using DC-DC converters and LDOs. I have knowledge on op-amps, sensors and actuators, and have thouroughly used WIFI SoCs like ESP8266. I can not only layout a PCB and sketch a 3D casing, ...
    Passionate for electronics, I enjoy working with microcontrollers, FPGAs, Arduino, Rpi. I can also custom design your power supply using DC-DC converters and LDOs. I have knowledge on op-amps, sensors and actuators, and have thouroughly used WIFI SoCs like ESP8266. I can not only layout a PCB and sketch a 3D casing, but also help you select the right part/technology for the best solution to your project in terms of cost and reliability. I am fluent in spanish, english and french. Do not hesitate to contact me! daha az
  • haris021 adlı kullanıcıyı işe alın
    2.5
    1 değerlendirme saatlik $5 USD
    I have Bachelors in Electrical Engineering and holds Masters Degree in Energy Systems Engineering with 3 years of professional experience in field of renewable energy. Publications: •Trends of terrestrial water mass in Indus Watershed over period of time using GRACE data. Presented in 6th Annual Pacific Northwest...
    I have Bachelors in Electrical Engineering and holds Masters Degree in Energy Systems Engineering with 3 years of professional experience in field of renewable energy. Publications: •Trends of terrestrial water mass in Indus Watershed over period of time using GRACE data. Presented in 6th Annual Pacific Northwest Water Research Symposium Oregon State University, USA. •Schultz, S., Saracco, S., Ajaz, W., Siddique, S., Clark, C., Mushtaq, H. and Ayub, M., 2016. “Eugene-Based Electricity Generation: Optimizing Resiliency for Eugene Water and Electric Board – Phase II”, Oregon State University Policy Analysis Laboratory (OPAL). Expertise: 1-Renewable Energy 2-Solar System Designing 3- Article writing, Technical Writing, Research with APA, harvard, IEEE referencing. 4- Presentations(MS PowerPoint) Software's/languages: RETSCREEN, MATLAB, Homer, Python, R daha az
  • MrDmytro adlı kullanıcıyı işe alın
    2.0
    1 değerlendirme saatlik $28 USD
    Electronic engineer, software engineer, system engineer. I develop custom electronics of any level of complexity. I have a well-equipped laboratory - prototyping is possible. I program for such microcontrollers: - ATmega (Arduino also) - STM32 - PIC For the development of printed circuit boards, I use Altium...
    Electronic engineer, software engineer, system engineer. I develop custom electronics of any level of complexity. I have a well-equipped laboratory - prototyping is possible. I program for such microcontrollers: - ATmega (Arduino also) - STM32 - PIC For the development of printed circuit boards, I use Altium Designer or (at the request of the customer) Eagle. Extensive experience in the development of embedded systems, automation systems, switching power supplies and inverters. daha az

Selam , işte bazı çevrimdışı freelancerlar

Selam , işte "" anahtar kelimeleriyle eşleşen bazı çevrimdışı freelancerlar