Mouser işler

I'm looking for an expert in off-grid systems to create a battery-powered solution for a refrigerator and an automatic gate system. - The system will need to be designed to support less than 6 hours of operation for both per day - Additionally, include a real-time monitoring system to track power usage and system performance. The ideal freelancer for this project should be experienced i...and input status (battery or AC) Need to have a button to manual switch from ac to battery Need to have fuse to protection Keep in mind, it has high current peak at load start! Prefer NOT micro-controller (except battery monitoring system) - Use Analog if possible! Need: - PROJECT - SCHEMATIC (prefer - not mandatory - easyEDA) - PCB (prefer - not mandatory - easyEDA) - Bill of materials (prefer...

...implements various memory protocols that runs on a Lattice FPGA (MachXO2 LCMXO2-4000HC). The FPGA is used as a high-speed data bridge between an ARM based microcontroller and a connected memory device (using SMC). This project is to expand the existing project and add support for the eMMC protocol and eMMC Flash memory devices. For testing, we have acquired various 64GB devices that are available on Mouser and DigiKey. Basic functionality is required: reading/writing/erasing with legacy speeds and 1,4,8-bit data bus. Project can be extended to include additional modes / features. The project is in Lattice Diamond, and written in VHDL. All work must be done to the existing project. And tested using exported bitstream binaries. Note: if you want to make a bid, please respond wit...

...implements various memory protocols that runs on a Lattice FPGA (MachXO2 LCMXO2-4000HC). The FPGA is used as a high-speed data bridge between an ARM based microcontroller and a connected memory device (using SMC). This project is to expand the existing project and add support for the eMMC protocol and eMMC Flash memory devices. For testing, we have acquired various 64GB devices that are available on Mouser and DigiKey. Basic functionality is required: reading/writing/erasing with legacy speeds and 1,4,8-bit data bus. Project can be extended to include additional modes / features. The project is in Lattice Diamond, and written in VHDL. All work must be done to the existing project. Note: if you want to make a bid, please respond with your previous experience with working with e...

I am seeking an experienced Electronics Engineer to develop a boost converter circuit capable of converting 48v DC 4.800w to 320v DC with a power of around 3500w. Key project requirements include: - Design a boost converter for increasing voltage output - Easy design PCB and schematic in KICAD - Use components that is easy to buy from Mouser our other company in EU - Use most SMD components Ideal skills and qualifications: - Proficiency in circuit design and simulation - Deep understanding of Boost converters - Experience with wide variety of components (Semiconductors, Passives & Integrated circuits) - Proven track record in delivering high power, high efficiency circuits. Your final deliverables will be a detailed schematic diagram, list of components with ordering detail...

I need a highly skilled freelancer who can develop a robust web scraping tool. The tool will primarily be use...efficiently scrape text content only. - Data format: The scraped data should be delivered in JSON (JavaScript Object Notation) format. - Database integration: Please note that the tool needs to integrate with a MySQL database for seamless data storage and retrieval. The goal is to get pricing information, stock availability and lead times for electronic component from website like Digi key and mouser. Please submit your bid, and any similar work will be good to see. I'm looking for someone who brings comprehensive experience in web scraping, JSON, and MySQL. If you are confident that you meet the given criteria, kindly submit a proposal. Let's create something ...

...is an open source PCB reference board. The source files need to be converted into KiCad7 as the schematics are available in .brd files. The project is primarily to get the PCB files converted to the KiCad7 project and then validation of the correctness of the board. Specific Requirements: - The PCB design needs to be compatible with specific components that are available in DigiKey, Arrow and Mouser. - I need someone who can work closely with me to ensure that the design meets my specifications and requirements. - The ideal candidate should have a strong understanding of KiCad and be familiar with designing PCBs for commercial products. - There may be small changes required to the board specifically moving the connectors around the board but largely (95%) of the design is to...

We have an existing VHDL project that implements various memory protocols that runs on a Lattice FPGA (MachXO2). The FPGA is used as a high-speed data bridge between an ARM based microcontroller and a memory device. This project is to expand that to add eMMC support, such as typical 64GB eMMC 5.1 devices available on Digikey/Mouser. Basic functionality is required: reading/writing/erasing with legacy speeds and 1,4,8 bit data bus. Project can be extended to include additional modes / features. Note: if you want to make a bid, please respond with your previous experience with working with eMMC devices.

Design a Qi compatible wireless charging receiver (RX) unit for 10 - 15W. - receiver antenna coil must be small, either 1) 24mm diameter or less, or 2) 20mm x 40mm or less - 10W+ receiving power at 6mm - when possible for capacitors and resistors use 0603 (metric) size parts - use parts available for purchase on digikey or mouser - provide 2.54mm header for external connection to +/-

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.

...returns in that time. -i.e. load disconnecting replay should be after the point where the 2 supplies join. PCB smaller than 100mmx80mm. Battery state indication. charging CC, Bulk, float, 24V, estimate of battery charge (5 LEDs) - This is open for discussion on best way to do this. Also indicate when shutdown is initiated and when it is done. Components must be readily available from digikey / Mouser and PCB must be JLCPCB compattable KICAD or proteus for the design. Ideal Skills and Experience: - Experience in battery charger design - Knowledge of schematics and PCB design - Familiarity with low voltage cutout and shutdown notification systems - Understanding of lead acid batteries and their charging requirements - Ability to incorporate overcharge protection into the design -...

The goal is to design a schematic to have a power-supply-circuit for an IoT module. Required specs : - Input 5v to 12v (if circuit can accept more than 12v, welcome !) - Input type are : external p... - Some help links : - - Guidelines : - Max PCB size (dual-side) must be 40x30mm - Simplest as possible (the less or cheaper components) - Easy to find component (AliExpress, Mouser, ...) - Easy to hand-soldering component (ideally min. 1.27mm pin space) - soldering-iron or hotair-gun - Min. 0805 SMD size Result : - Must be done with KiCad - Full schematic + fully routed PCB

Circuit #1) The goal is to have a circuit to give/cut power (+3.3v / +5v) to sub ICs/sensors, command by a microcontroller pin. Must cut the input voltage (circuit must be placed between VCC and IC) = high-side switch. Circuit #2) The goal is to have a circuit to enable/cut I2C bus (+3.3v...sensors to be connected on the same I2C bus - what about pull-up resistor ? Remarks: If power is cut (by circuit #1), power must not leak through I2C pull-up resistors. Maybe circuit #2 is not necessary if we can be sure that no current leak through pull-up resistors when cut the power. Guidelines : - Simplest as possible (the less or cheaper components) - Easy to find component (AliExpress, Mouser, ...) - Easy to hand-soldering component (ideally min. 1.27mm pin space) - soldering-iron or ...

...shall not be utilized. - The PIC16 shall utilize serial communications to store the number of events. Events are defined by a) power on to power off cycle, b) battery temperatures falling below 2.5V, or c) battery temperatures rising above 132°F. - Note: all limits are established as variables in the program Scope of project: A) Design the schematic utilizing standard components from Digikey, Mouser, RS, Newark. Furnish .sch file(s). Write and prove the code for the PIC16. Code shall be written with supporting comments per line explaining the code's purpose on that line. Prefer to stay away from high-density (e.g. QFP100 type, fine-pitch) components. Milestone 1 (40%) - We will breadboard the design and test the code. Milestone 2 (50%) - Joint debugging of schematic...

Induction Heater PCB Design and Manufacture I am seeking an experienced professional to assist with the design and manufacturing of an induction heater PCB. The project requires the following specifications: - Cost-effectiveness and reliability - Parts (bomlist) must be available from well-known suppliers such as Mouser, digi-key, etc. - Provide support for issues during manufacturing - Existing induction heater designs can be used, but it must then be adapted to our requirements. PCB requirement: - Works on 230v AC - Main control by ESP32 S3 with WiFi - RGB LED - 1x touch control - 1x sensor temp (max temp 120 Celsius ) - Control 2x 12v pump - 1x buzzer - Induction will be turn on by ESP32 and current can me adjust by ESP32 - Max power induction 3500Watt Firmware will be desig...

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.

... - The PIC16 shall utilize serial communications to store the number of events. Events are defined by a) power on to power off cycle, b) individual battery temperatures falling below 2.5V (recorded with battery # as 1-4), c) individual battery temperatures rising above 132°F (recorded with battery # as 1-4). Scope of project: Design the schematic utilizing standard components from Digikey, Mouser, RS, Newark. Furnish .sch file(s). Write and prove the code for the PIC16F17146. Code shall be written with supporting comments per line explaining the code's purpose on that line. Prefer to stay away from high-density (e.g. QFP100 type, fine-pitch) components. Milestone 1) We will breadboard the design and test the code. Milestone 2) Joint debugging of schematic and code. F...

I am designing a display adapter board. I am looking for an experienced freelancer who can assist me in finding the pinouts, electrical specifications, connector type and datasheets for the display of the Samsung Galaxy Tab A...connector type and datasheets for the display of the Samsung Galaxy Tab A7 Lite SM-T220. The display has a MIPI DSI interface and a 40-pins connector. But MIPI DSI doesn't have standardized connectors or pinouts. And I cannot find schematics for the display or the motherboard. I need this information so I can design a display adapter board. Deliverables: -connector type with order number (from Mouser, Farnell, or RS components) -pinout table -electrical characteristics for power (voltage and current) -electrical characteristics for backlight (voltage a...

- The SOM that we would be using is the MYC-Y6ULY2-V2-4E512D-50-C, 512MB RAM variant. The datasheets and some reference schematics are ava...datasheet) o 4USB Ports (may or may not need a 4usb hub chip) o 1 Ethernet Port o WIFI Module o 12v Power Input (Refer Development board schematic) o 1 Momentary Push Button o 2 RGB LED o (Micro USB port/Type C port for flashing the code) o SD Card for development variant LINKS TO DATASHEETS: MYC-Y6ULY2-V2-4E512D-50-C Overview : Mouser Product: Development board data sheet, Pinout, etc (Go to Downloads): Do let me know If any other docs are required

...already have the following operational amplifiers, so if they could be used and meet the functional requirements, that would be beneficial: Mouser Part Numbers: 595-LM358P, 595-LM311P, 595-TL072CP, 595-TL082ACP, 926-LMC6482AIN/NOPB. The final deliverables will be: - A complete electrical schematic showing the connection to the monitored circuit (V+, V-), the connection to the microcontroller digital input, connection to the microcontroller ground (GND), and any +3.3V supply requirements from the microcontroller. - A list of the components in the electrical schematic, including the full Mouser Part Number (P/N). - It is not necessary to list the Mouser part number for any standard electrical components such as resistors or capacitors, but the values (ohms, ...

We would like to have a simple PCB designed, manufactured and tested using the Lattice Semiconductor SIL9437 HDMI eARC IC. Our offer is to pay for the development, prototype manufacturing, and design files upon completion of verified and tested module. More information on the IC here:...design files upon completion of verified and tested module. More information on the IC here: This small PCB will be about the size of a credit card (or smaller), have an HDMI input, and 8 channels of PCM audio via 4 lanes of I2S output on a header. This IC is now available to purchase at Mouser: Thanks, Mike

...of details is required Altium Designer Expert for Super Fast Schematic/PCB Layout work Complete Design in Altium including Schematic and PCB with all output files/libraries/footprints/Bom/mechanical drawings ETC... Super Compact, Cost effective yet Impressive electrical characteristics Complete Schematic needs to be created using easily sourced components (sourced through LCS/JLC/Digikey/Mouser/Avnet/etc) Full payment will be rendered upon review and approval of final design files by IC mfg. - Libraries of Components including Components Schematics and Footprints need to be made - Project Files Should be Production Ready Output Format, including complete BOM and Gerber/pick-place files - Design must be safe; the device must operate reliably. - Design must be optimize...

...projects All project details provided once we see some of your work and chat about it Complete Design in Altium including Schematic and PCB with all output files/libraries/footprints/Bom/mechanical drawings ETC... Super Compact, Cost effective yet Impressive electrical characteristics Complete Schematic needs to be created using easily sourced components (sourced through LCS/JLC/Digikey/Mouser/Avnet/etc) Full payment will be rendered upon review and approval of final design files by IC mfg. - Libraries of Components including Components Schematics and Footprints need to be made - Project Files Should be Production Ready Output Format, including complete BOM and Gerber/pick-place files - Design must be safe; the device must operate reliably. - Design must be optimi...

Only a hardware development is required. No code. Time for project development: max 6 days. Sensor used for input: piezoelectric Microcontroller used to receive the amplified sound: ESP32. Output voltage range: 0-3.3V. Midpoint Bias near V=1.65V (half of 3.3V) Operational Amplifier model will be defined before start the proj...sensitivity signal. Signal amplification should be the higer possible. In oder to avoid the noise, a 10-15Hz filter can be used. We can cut any input or output signal above a specific voltage threshold Battery used: 1x3.7V (voltage used as input for sensor = 3.3V) Software to use: KiCad for schematic and any other software for simulate it (for example LTspice). Project files will be provided. Mouser reference will be used for the BOM. ()

Crear el schematic y PCB para un dispositivo compuesto por ESP32 y MC60 de Quectel. Hay 3 entradas: 1 análogo, 1 GPIO, 1 I2C. Batería externa de 3.6V PCB de una sola capa. La dimensión y formato de la placa ya la tengo definida. Software: KICAD. El entregable es el proyecto completo, incluyendo el BOM de Mouser. Los demás detalles se proporcionarán una vez comenzado el proyecto.

We have designed a small blue tooth module that will control a supply relay. The application will send a limited number of commands to the module for operation. Facility will be needed for pairing, storing a simple user code, operating the relay and the ability to override when the App is faulty or unavailable. A software development kit is available from Mouser and we will provide or assist with the provision of any hardware needed. Our software engineer will provide a list of blue tooth commands to be sent from the App.

Design pcb to house an esp32 module and associated electronics to make distance measurements from 10mm to 140mm. Accuracy within +/-10mm. The ultrasonic sensor needs to be mounted external to pcb via a connector. Do not want ultrasonic modules on pcb, u must design that circuit yourself. The esp32 will be going into deepsleep, so u must shutdown any current that will drain the ...The ultrasonic sensor needs to be mounted external to pcb via a connector. Do not want ultrasonic modules on pcb, u must design that circuit yourself. The esp32 will be going into deepsleep, so u must shutdown any current that will drain the battery. Pcb must accept battery holder. Deliver the following: pcb, schematic and libraries (kikad or eagle) Manuf gerbers Excelfile with bom (digiket, mouser or...

Design pcb to house an esp32 module and associated electronics to make distance measurements from 10mm to 140mm. Accuracy within +/-10mm. The ultrasonic sensor (SR04T waterproof sensor) needs to be mounted external to pcb via a connector. Do not want ultrasonic modules on pcb, u must design that circuit yourself. The esp32 will be going into deepsleep, so u must shutdown any cur... see image Details on sensor: Only use SR04T Waterproof Ultrasonic ,see article.. Deliver the following: pcb, schematic and libraries (kikad or eagle) Manuf gerbers Excelfile with bom (must have digikey, mouser or RS links)

...of the LEDs should be controllable via PWM. Your task is to design a PCB with the above requirements with... 1. Analyze the power consumption of the system -- these are high power LED and an RPi has limited current supply to peripherals - your design must take this into consideration. 2. Use only specific LEDs mentioned above. 3. Source other components (resistor/capacitor/mosfet/ic/etc) from Mouser India () ensuring that the component is in stock and can be dispatched As deliverable you will provide: 1. Circuit diagrams and schematics of the system. 2. CAD model (step file) of the assembled PCB so that it can be integrated with our mechanical designs. 3. Designer files (Altium/KiCAD/etc) 4. Gerber files, pick and place files, and formatted BOM which can be sent to a vendor ...

I need someone to forward me orders from Mouser and Digikey. Preferred is someone from EU country. I have several orders monthly and your job will be to forward them to me. Should be easy and straightforward job. What i am usually ordering are semiconductors like mosfets transistors diodes etc etc. Thank you.

I need someone to forward me orders from Mouser and Digikey. Preferred is someone from EU country. I have several orders monthly and your job will be to forward them to me. Should be easy and straightforward job.

...have fuse holder with fuse down to 2A for the track width. The probe I’m using have only micro-grabber tip, so ideally I would like to connect on some kind of test point, as shown below. So in the drawing in attachment, the plan was to install the PCB board inside a plastic box, have my cable that are connected on the top. I was thinking of using the following terminal to connect theses cables: Mouser #:651-1740000 all we need is a track that goes from the terminal on one side to the hook terminal on the other. I’m looking to purchase the fuse holders that will be DIN rail mounted in a box that will protect the whole PCB board. The fuse will be 2A 1500VDC. Digi-Key Part Number 18-SPXV002.T-ND We are planning to connect the whole system on different sources, with...

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.

Please do not send a generic message, answer the project details. Development and design of turnkey system components in a single embedded board. An electronic board plus basic configuration software. The expectation is to design a circuit that uses boards/chips/circuits/systems that exist in western sources like Mouser, Digikey and etc. Would be used in the USA, Canada, Latin America and if possible can pass or avoid FCC certification by using components or design that does not need one. It should detect at least 100m or more. The purpose of the project is: To install a radar with a narrow beam that can detect human movement crossing the narrow beam from left to right or right to left, apply an algorithm to rain, snow, avoid birds, small animals, branches waving in front of it. ...

Please do not send a generic message, answer the project details. Development and design of a turnkey system component to embed in a board from A to Z of an electronic board plus basic configuration software. The expectation is to design a circuit that uses boards/chips/circuits/systems that exist in western sources like Mouser, Digikey and etc. The purpose of the project is: We have a board that can sense vibrations from a coax-like cable, I would like to add another layer based on TDR and locate those vibrations, the typical length of cable is up to 300m/1000ft. The detection and location will be combined into 1 solution that provides an alarm with a specific location. This circuit will be embedded into our board, our current processor is a PIC32. ANSWER SPECIFICALLY: Do you ...

Design PoE Injector. On the schematics page 1, it is 10/100Mbps normal Ethernet port designed. Need to add PoE injection to supply power to the IP Camera at the other end of Ethernet cable. On the page 5, there is a 48V non-isolated boost conver...is 10/100Mbps normal Ethernet port designed. Need to add PoE injection to supply power to the IP Camera at the other end of Ethernet cable. On the page 5, there is a 48V non-isolated boost converter, but it would be better to have an isolated 48V supply instead. Restrictions: 1. Only need schematic design, preferred in EasyEDA format. 2. All components must be in stock in one of LCSC, Digi-Key, Mouser. the most preferrable option is LCSC. 3. all passive components - R, L, C, need to be 0603 or 0805 packaged, except high-voltage elctryle c...

We are exploring the use of the ST Micro STNRG388A power conversion digital controller integrated circuit for a family of multi phase DC-DC converters from 2kW up to 600kW. We currently have four STEVAL-ISA164V1 evaluation boards available from both digikey and mouser that we need firmware coding support for. The evaluation will grow in phases of increasing complexity. The first phase of this firmware will generate 3 interleaving PWM outputs that vary from 1% to 99% . The output percentage would vary proportionaly to a single analog input voltage that will be provided to an analog input pin on the eval board. The switching frequency will be 250 Hz. This first circuit will power up and then start putting out a set of 3 identical square waves (PWM outputs on digital pin) that a...

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.

Hi, I'm wanting a circuit board / pcb created. Input volts is 12v. (standard size female input module) Two lots of power distribution voltage. 6 x 12v. 4 x 6v. Input power should have a fuse holder 3AWG or compatible before it goes to the rest of the outputs. There should be a small capacitor between the input and the outputs to keep load steady. https://au.element14.... 6v outputs should use There should be LED indicators to show 'voltage / working / power' As well as test points for input and output voltages. All parts should be available on element14, ebay, mouser etc etc. Thanks T

I have basic soldering experience and I am looking for the easiest way to build a solar engine to power an ESP-32 device with a power-hungry peripheral. I already have solar panels (6V) and capacitors large enough to power the device for th...to power an ESP-32 device with a power-hungry peripheral. I already have solar panels (6V) and capacitors large enough to power the device for the duration of the process. The missing part is a controller board. Of the dozens of so commercially available, I have found none that is able to deliver that 800mA - 1A I need. I need the list of components (BOM), with code from some supplier (example mouser or digikey or other). Payment in 2 steps: once the project and the components are well defined (70%) and once I successfully put the parts toget...

I need all editable files and also in production format (gerber). I also need the list of components (BOM), with code from some supplier (example mouser or digikey or other). I need all component libraries used in eagle Supply voltage (8 to 36V) Characteristics: 5 input(negative) 5 outputs (negative) (Mosfet output 250ma) 1 serial(RS232) port 4 - pins to configure ESP32(tx,rx,3.3v, gnd) 2 ports for one wire dallas temperature sensor DS18B20 5 pins remaining, 5 for IO, directly on esp32 and 1 negative pin Payment in 2 steps: 1) After completing the electronic scheme 2) After completing PCB

I need all editable files and also in production format (gerber). I also need the list of components (BOM), with code from some supplier (example mouser or digikey or other). I need all component libraries used in eagle For the firmware I need all used libraries, source code and compiled. use the following components STM32F030CCT6 G510-GL LCC (GSM, GPS) RF69(RF Module) Lithium battery 2500ma You should use flash memory to store up to 1000 positions, when I have no gprs signal (download in fifo mode). Tracker must have USB connector to: configure equipment and charge the battery, panic button and accelerometer. Firmware must have following requirements Transmit and receive TCP socket Update firmware via FOTA Activate RF module only when there is no GPRS signal Receive config...

Create a project in AD17 (or higher), create (redraw) schdoc from , set rules for the lines, fill elements parameters and manufacturer partnumbes (digikey/mouser); create pcddoc document with board outline and arrange elements, board trace is not required. Links

...from as shown with name, email. Part number etc… 10) Update footer Arenacommerce to Fastron Electronics 2021 -> update with year 11) Configure Searchanise (search application) for new theme 12) Help to have 4 filter group working. (we could only get one filter group working on 5.0) 13) Custom Blog Template -> smaller image size 14) Customer product List template -> similar to mouser or digikey 15) Order acknowledgement does not show the discounted price paid ...

...of the given PCBs (most Parts should be clear by their labelling, only the MLCCs might need disassembling and double checking with multimeter) - drawing schematic accordingly - double checking schematic with design recommendations of the corresponding ICs datasheets - making sure each parts is assigned the right footprint - add attribute "supply source" to each part, with either a link (digikey, mouser, taobao etc) or ordering number at LCSC - Part values should be in the following format: - resistors (assuming 1% standard precision): "0R002 / 0.5% / 100PPM", "3R3", "499R", "2k2", "100k", "100k / 0.5%" - capacitors (voltage means minimum voltage, 20% standard precision, X5R standard): "12p / 50V (N...

... Output Files, Schematic Etc. I envision module to be 4 layer, RF edged GND, shield covered, no larger than 20mm by 60mm inside it will hause DC section USB Port charger Lipo batt secion with connector and Analog headset connector as well as space for PCB mounted fanstel module BT-40 E Altium Footprint MAX77757 https://www.snapeda.com/parts/MAX77757JEFG435+/Maxim%20Integrated/view-part/?ref=mouser datasheet MAX98050 SJ-43516-SMT-TR Headphone connector or similar MAX98357A Audio Amp for speaker small audio AMP circuit will also be required, D lines to C port will have to be MUX connected for programming BT module I need the project to be Clean and Ready for Production each and every step of the Way , even if parts of

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.

We are developing a custom embedded board which is 90% complete in schematics and board placement is done. The freelancer needs to complete the pin assignment, do the routing for the same in Eagle software, prepare BOM and part list for procuring from Element14, Mouser. The board is a 4 layer board and approx dimensions are 130mmx130mm. The schematic and board files pdf are uploaded for reference.

I need help building a basic variable load circuit. I have a wind turbine that I am building that I want to be able to change the load of the circuit to increase the resistance on the motor and optimize power generated in different wind conditions. The relays needs to be able to withstand up to 100v. I have the basic design laid out, I just need help finalizing and picking the correct part...withstand up to 100v. I have the basic design laid out, I just need help finalizing and picking the correct parts. Current idea: - 4 Wire Wound Load resistors: 1A, 2A, 4A, 8A - Relays to allow the raspberry pie to change total load - Basic voltage divider in parrallel to measure the voltage through the circuit Any parts required to build the circuit should be able to be ordered from digikey or ...

Hello, I am looking for someone to help me source electronics components every so often. I'm mostly interested in parts from mcmasters-carr, mouser, digikey, or aliexpress, however I'm open to buying from other places as long as they are reputable vendors. I am specifically looking for small parts that will fit with Raspberry Pi project kits that I am working on. Please bid the rate you would like to charge per component, if hired. The first part I need help finding is a wire connector that will snap connect to the bottom pins of these LEDs without needing to solder anything: The other wide of the wire should be a small male pin like the one shown here:

I am looking for someone to help me source electronics components on an ongoing basis. I'm mostly interested in parts from mouser, digikey, or amazon, but someone who can also find cheaper parts oversees would be a bonus. Please bid the rate you would like to charge per component. If hired. The first part I need help finding is a board mount version of these iec plugs.