Openocd işler

I want to flash my stm32 through raspberry pi using openocd. I can flash but i need help in read out protection. Make read protection level 2 using openocd.

I am working on a healthcare project where we are using a load cell. We have a Nordic nrf51 series bluetooth chip with several peripherals up and running. We are using openocd and 2 pins to program it. We need to connect also a load cell to the ADC and perform the calibration and perform careful testing with this load cell to study its drift and errors. Since it's a hardware / embedded s...

I am working on a healthcare project where we are using a load cell. We have a Nordic nrf51 series bluetooth chip with several peripherals up and running. We are using openocd and 2 pins to program it. We need to connect also a load cell to the ADC and perform the calibration and perform careful testing with this load cell to study its drift and errors. Since it's a hardware / embedded s...

Hi Cumali., In order to communication with you I need to provide a budget. After we talk about your ability we can talk about the complete project budget. I will then officially post the project. I noticed your profile and would like to know if you have the time and experience to write a OpenOCD driver for customer NVM to be user with Eclipse. I can provide the NVM interface specification and po...

I am able to upload a program using st-link application however if I upload within eclipse AC6 as provided by ST I get the following errors With a generic stlink v2 Open On-Chip Debugger 0.10.0-dev-00019-g5352c55 (2019-02-14-15:45) Licensed under GNU GPL v2 For bug reports, read [URL'yi görüntülemek için giriş yapın] srst_only separate srst_nogate srst_open_drain conne...

I need someone to help me fix my config file. Im right now can sometimes flash the whole 6 devices in a daisy chain but most of the time i fail. Im not familiar with this field so its difficult for.

I'm using Jtag and OpenOcd for my project and need someone to help me fix my config file. Im trying to flash the devices one by one in a Daisy chain but i received this Error TARGET: [URL'yi görüntülemek için giriş yapın] - Not halted. when i dont put it in a Daisy-chain. it works perfectly but in a Daisy chain with Jtag, it does not

Hi Duc D., bạn giúp mình với, mình đang cần flash 6 target, mình sử dụng JTag với OpenOCD. Giúp mình với nhé.

Hi HeshamOmr, I have trouble flashing multi devices using Jtag and OpenOCD. Pls help me

Hi websat13, I have trouble in flashing multi devices using Jtag and OpenOcd. Pls help me

Hi David U., I'm having problem in flashing multi targets using Jtag and OpenOCD. pls help me

Hi Rog T., I have trouble in flashing multi targets with Jtag and OpenOCD. pls help me

Hi Khawaja Muhammad A., I have trouble in flashing 6 devices in a daisy chain. im currently using Jtag and Openocd. pls help me

Hi MUhammadt429i,i have trouble in flashing 6 devices in a daisy chain. I'm currently using Jtag and OpenOCD. pls help me.

Hi Goitom Y., i have trouble with Jtag and Openocd. Can you help me i think its not a big problem for you.

Hi Goitom Y., i have trouble with Jtag and Openocd. Can you help me i think its not a big problem for you.

I'm using Jtag and OpenOcd for my project and need someone to help me fix my config file. Im right now can sometimes flash the whole 6 devices in a daisy chain but most of the time i fail. Im not familiar with this field so its difficult for me but for expert its just like piece of a cake.

Develop STFT Algorithm using matlab and converting it to c code to be implemented in Eclipse IDE, if you are able to do it in Eclipse, it's better. The whole project scope is attached in the image below. Tools: STM32F429 DISCOVERY, OPENOCD, STLINK-V2 Note: I will explain more about the project during chat, Also, the price i set is an amount which would get better bids, the range is a bi...

Develop STFT Algorithm using matlab and converting it to c code to be implemented in Eclipse IDE, if you are able to do it in Eclipse, it's better Tools: STM32F429 DISCOVERY, OPENOCD, STLINK-V2 Note: I will explain more about the project during chat, if you are interested,send a message. i will select the lowest bidder as i believe this is a simple project if you already have the experi...

Looking for someone with experience doing entropy in C before. More details will be shared during chat. Software Tools : Eclipse IDE, OPENOCD, ST-LINK Hardware: STM32F429ZI-Discovery board

Tools: stm32f429-Discovery board, Software tools: Eclipse, OpenOCD debugger, ARMGCC toolchain, ST-Link-v2 Brief Objectives: Codes are mostly done, just need some debugging and final alterations to make it better. Mainly, to delay the string displayed after reading file to last for only 3 seconds. Also, to make sure the variable is storing all data of the .wav file. SDRAM is used for large file ...

Hi freelancers, my budget is kind of tight around (10-60$) & i'm looking for someone i can closely work with and communicate. Tools used: STM32F429 , OpenOCD, STlink-V2 libraries: TM library, HAL library SDcard: 16GB fat32 format. preferred platform to comm: Skype, apply if you are interested and i will share objectives needed. This project should not take longer then 3 days as i&#...

Tools used: Eclipse, OpenOCD, STlink-v2, ARMGCC compiler Board: STM32F429I-Discovery Objectives: To display a clean fft spectrum on the LCD, a clean voltage peak. Criteria: We need this done asap, and we need someone committed to chat and also explain to us why you did it that way. Communication through skype.

Title: Develop FFT in embedded system using eclipse as the IDE. Tools: Uses ARM GCC as the compiler Uses GNU ARM Eclipse as the toolchain Uses OpenOcd as the debugger Sample codes taken from STM32CUBE library. Description of the project: Need to integrate DAC, ADC, LED and FFT codes together using embedded c programming. We will be using stm32f429Zi disco...

Title: Develop FFT in embedded system using eclipse as the IDE. Tools: Uses ARM GCC as the compiler Uses GNU ARM Eclipse as the toolchain Uses OpenOcd as the debugger Sample codes taken from STM32CUBE library. Description of the project: Need to integrate DAC, ADC, LED and FFT codes together using embedded c programming. We will be using stm32f429Zi disco...

We need a debugging environment set up using OpenOCD. Our board uses the Nuvoton W55FA93 CPU which is based on the ARM926EJ-S. The connection is made with a raw USB cable to 5V, DP, DM, and GND pads. We need a C/C++ Eclipse build environment set up that will work with this board and debug from Eclipse. We do have a TurboWriter tool but it is not supported by the manufacturer and it is not work...

Basically I have a Mifare Classic 1K and HID Proxkey RFID tag that I need duplicated, but I am having trouble compiling the required tools on Linux myself. I have a Proxmark3 with both LF and HF antenna: [ [URL'yi görüntülemek için giriş yapın]] And a Bus Pirate which is needed to flash the Proxmark3: [ [URL'yi görüntülemek için giriş yapın...

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.