Wifi işler

ESP32 tabanlı, GSM hatlı bir endüstriyel cihaz geliştiriyorum ve projenin omurgasını oluşturacak gömülü yazılıma öncelik veriyorum. Cihaz; SimCom GSM modülü, RFID/NFC etiket okuyucu, 2 analog giriş, 3 röle çıkışı, 1 PWM kanalı, ayrıca ekran ve tuş takımını içerecek. WiFi ile Bluetooth’un birlikte aktif olduğu bir mimari planlıyorum; uzaktan güncelleme / servis kolaylığı da hedefler arasında. Uygulama tarafında cihaz, sahadan GSM üzerinden yaklaşık 200 iş emri alacak, bunları sıraya koyup tamamladıkça yine GSM üzerinden sunucuya raporlayacak. İşlem güvenilirliği, güç kesintisine dayanıklılık ve hat içi (OTA) güncelleme kabiliyeti kritik. Elektronik tasarım ihtiyacım da var...

Projede bir adet step motor, sıcaklık-nem sensörü, gaz sensörü (MQ-2) olacak. Android/IOS uygulamasından wifi şifresi girilerek kurulum yapılabilmeli. Proje modem bağlantısı ile uzaktan kontrol edilebilecek. Sensörden gelen veriler uygulama üzerine canlı akacak ve log kaydı olacak, üst alt limit değerlerde bildirim yapılacak. Step motor mobil uygulama üzerinden açısal kontrol edilebilmeli Batarya durumu anlık takip edilebilmeli. Andoid/IOS uygulama tasarlama ve kodlama alanında tecrübeli, ardunio projeleri geliştirmiş bir kişiden hizmet almak istiyorum. Beklentilerim : Projede sonrasında ufak arayüz değişimleri konularında da destek talebim olabiir, Projenin donanımları bende mevcut, devre kartının tasarımı, kodlaması ve uy...

8 adet step motoru aynı da çalıştırabilen bir elektronik devre kartı olacak, ölçüleri ve motor bilgileri verilecektir. 8 adet step motor süren devre kartları birbirlerine bağlanabileceklerdir. 485/232 veya benzeri bir bağlantı ile , üzerinde wifi modül olacak ama isteğe bağlı olarak master devreye eklenecek , diğer devrelerde kullanılmayacaktır.

esp32 Wifi ile Firebase'e bağlanacak, telefon Mac adreslerinin listesini alacak, Bluetooth ile sürekli etrafını tarayacak, listedeki Mac adreslerinden birisi menzile girdiğinde bir röle çalıştıracak.

...verilmek üzere bir cihaz tasarlamamız gerekiyor. Bu cihaz 13.56 mhz RFID'leri okuyacak bir RFID modülü ve RFID'den okuduğu kart ID'sini kendi ID'si (Cihazın ID'si) ile birlikte (iki string değişkeni) Wifi üzerinden yazılımını bizim yapacağımız bir web api'ye gönderecek. Web api ile bu veriler bizim veri tabanımıza kaydedilecek ve şirketin istatistik verileri için kullanılacak. Yani yine fabrika örneğinden düşünecek olursak, gün içinde hangi usta (yani hangi cihaz) hangi rfid kartlarını ne kadar sıklıkta okutmuş gibi. Sistemin genel mantığı bu şekilde olacak. Tasarlamamız gereken PCB; RFID okuyucu ve Wifi modüllerini içermeli. Aynı zamanda pil, buzzer, led, açma kap...

Nodemcu kullanılarak aynı ağda olan bir bilgisayar veya akıllı telefon ile yapılan aracı kontrol edilebilmektedir. Ara yüzde kullanılan sanal joystick ile aracın hızı ve yönü rahatça kontrol edilmekte. Videoyu çekerken joystick kısmını çekemedim ama ilgilenenler için detaylı olarak video ya da resim ile bilgilendirilirim.

blynk uygulamasına üç buton koymak istiyorum. birincisinde 28 byj-48 step motor bir yöne istediğim kadar tur, ikincisinde ters tarafa, üçüncüsünde ise bir tarafa dönüp iki saniye bekliip diğer tarafa döndürmek istiyorum. nodemcu'yada wifi ile telefondan kullanıcı adı şifre yazıp bağlanarak browserda bir ara yüz açılsın istiyorum ve blynkin auth kodu, nodemcunun bağlanacağı wifi'ın adı ve şifresini yazmak istiyorum. Elimde şuan kullandığım arduino ile yazılmış browser ara yüzü olan başka bir yazılım mevcut. buna Blynk uygulamasının auth kodunu yazabileceğim bir alan eklemek istiyorum. süreci hızlandıracaksa kodları gönderebilrim. browser görüntüleri ekliyorum. ...

Bir verici ile wifi üzerinden haberleşen adreslenebilir ledleri ortamdaki seslere göre renk değiştiren bir proje. Bu projede esp8266, Nodemcu v3 kullanılıyor. Bu projenin arduino kodunda sıkıntılarım var. Bu sıkıntının çözülmesi için paylaşıyorum. Bu projenin şemalarını aşağıda yükledim.

Merhaba ben arduino wifi modüllerini kullanarak çeşitli projeler dişinda mit appinvertor ile kendi apk uygulamami yapıp arduini kartları ile uzaktan kontrol yapabiliyorum.

Webrtc bir video konferans uygulamamız mevcut. Bu uygulamamızda Wi-Fi ve USB kameraları da kaynak olarak gösterebiliyoruz. Özellikle android ve IOS tarafında bu harici kameraları kaynak olarak göstermeyi sağlayabilecek birine ihtiyacımız var.

bu projede esp32 ile micropython kullanarak kendi block programlama uygulamamızı yapacağız wifi yada bluetooth üzerinden mobil geliştiricimiz bize kodları gönderecek bizede bu kodları esp32 üzerinde çalıştıracak programı yazacak kişi gerekiyor

proje kod adı: CİNGÖZ Proje webrtc ile yapılacak ilk hedef : hasta olan kayınvaldemi kamera ile uzaktan cep telefonumdan veya web sayfasından izlemek . Kayınvaldemin tarafında esp32 cam kamera olacak . bu webe en yakınındaki wifi üzerinden çıkacak . Wifi şifresi cep telden kare kod kameraya okutularak .IO. Adresi ve sifre kameraya verilecek . Android te ise kamera görüntüsü ve ses her iki yönlü olarak iletilecektir . Kamera pan tilt kontrol edilebilecektir. Yazılım open source olarak devredilecektir. Gizlilik ve koruma sözleşmeşi yapılacaktır. Donanımı ben hazırlıyacağım sonucta 3 yazılım gerekiyor 1. esp32 cam için( ben hazırlıyacağım ) 2. android cep tel için 3. .IO server yazılımı . b...

wifi calisacak coklu sensor PCB kart tasarımı + sensorlerden okunan bilgileri cihaza entegre LCD ekrana istenin formatta yazılması + sensorlerden okunan bilgileri cloud yapımıza gonderecek gomulu yazılım ve IFTTT entegrasyonu PCB UZERINDE OLACAK SENSOR VE KOMPENENTLER - PIR SENSOR - LUX (ISIK) SENSORU - ISI/NEM SENSORU - HAVA KALITE OLCUM SENSORU (pm2.5 + gaz sensor) - 180 DERECE IR (REMOTE KONTROL) SENSORU - 4.3 LCD EKRAN - RGB LED 3 ADET - BUTON 3 ADET (ISIKLI)

Bir proje çalışması için wifi aracılığı ile drone kontrolü yapabileceğimiz ve görüntü aktarımı alabileceğimiz bir uygulama yaptırmak istiyoruz. Uygulama içerisinde drone kontrolü (joystick), gerçek zamanlı görüntü izleme, uçuş verileri görüntüleme olacaktır. Çok profesyonel bir çalışma istemiyoruz. Yazdığımız istekleri karşılaması yeterlidir. Arayüz görsel tasarımları tarafımızca yapılacaktır. Uygulamayı geliştirecek arkadaşın IOT üzerinde çalışmış olması öncelikli tercihimizdir. Uygulama tek bir ekranda olacaktır. Menü gibi kısımlar gerekmemektedir. Ekteki fotoğrafların bizim tarifimizce yapılmış halini istiyoruz. Fotoğraflar temsilidir. Uygulama i...

Android Telefon ile önce arduino devre kartıma bağlanacak Wifi kullanıcı adı ve şifre gönderecek sonrada arduinonun firebase'e gönderdiği verileri programın içerisinde kullanacak bir program yapmak istiyorum. Yabancı Dilim olmadığı için sadece Türkçe bilen biriyle anlaşabilirim.

Arduino ile akvaryumun ısısı, ortamın nemi, elektrik durumu anlık olarak wifi ile yada gsm modül ile belirlenen web sitesindeki mysql veritabanına kayıt edilecek. Rf bağlantılı 8 li 220 volt kontrollü priz de web arayüzü ile kontrol edilebilecek. Kullanıcı web arayüzü ile prizleri açıp kapatabilecek yada uyarı alarm ayarlayabilecek. Uyarılar kullanıcının telefonuna sms olarak iletilecek. Android ve ios üzerinden uygulama ile bu verilere ulaşabilecek

Samsung J3,j4,j5,j6,j7 telefonlarda çalışacak aşağıda yazılı özelliğe sahip bir uygulama istiyoruz. ilgili telefonlara yüklenecek uygulama belli periyodlarda telefonun wifi bağlantısının açık olup olmadığını kontrol edecek ... kapalı ise otomatik açacak... yine aynı uygulama telefon üzerinde çalışan host adlı bir uygulamayı da kontrol edecek kapalı ise otomatik açacak... program telefonda local çalışacak ve çalışmak için internet bağlantısına ihtiyac duymayacak...

android uygulamasında ssid ve password yazarak wifi bağlantısı kurması. Daha önce hiç girmediği bir ağa girecek

...genişlik, 13cm yükseklik 2. ATMEGA 2560 Micro İşlemci Kullanılacak 3. Çift Katlı PCB isteniyor 4. Güç katı 12 V DC giriş 5 V ve 3.3 V luk çıkış beslemleri olacak. 5. I2C üzerinden ekran bağlanacak. Bu yüzden I2C için GND,VCC,SDA,SCL uçları olan header konacak. 6. Işlemcinin RX3 ve TX3 çıkışları bir jumper aracılığıyla wifi module veya gsm module gidecek. Jumper hangi tarafta ise karta o dizilecek ve çalıştırılacaktır. 7. Wifi için "ESP8266F" modülün kart üzerine konması yeterlidir. 8. GSM için QUECTEL M95 Module kullanılacaktır. Bu modul, sim connectorleri, anten konnektörleri ve gerekli componentler dizilecektir. 9. İşl...

...Save event presets Frame requirements: • PNG overlays with transparent background • Organised into categories • Admin ability to add/update frames ________________________________________ 5. Gallery Functions • View session photos • Download all photos via QR code • Admin “Delete All” function to wipe device between hires ________________________________________ 6. Settings Panel Must include: • WiFi configuration (can link to Android settings) • Max prints per guest limit • Printer status • Audio/visual preferences • LED brightness control • Optional sharing defaults enabled ________________________________________ 7. Cloud / Sharing Integration • Upload photos to server/cloud storage • Auto-genera...

...Visible) A) Clear System Mode Indicator (Required) There must be a highly visible, always-on indicator showing the current system mode: Log Settings Arm Disarm Home Arm SOS Notes: Color choices are free as long as the mode is instantly recognizable The indicator must be readable at a glance and feel premium B) Small System Icons (Required) Include these always visible system icons: Battery icon WiFi icon Charging icon (shows charging or not) LTE signal icon (classic mobile signal bars) C) Top-left mini elements (Required) In the top-left corner, include: A small mini clock A small mini status icon (simple system-style icon) 7) Logo Requirement (Contest Phase Placeholder) A logo must be integrated into the design. For contest entries: Use a placeholder horizontal logo Five l...

I need a plastic enclosure designed for a screen-free WiFi kids phone. The design should be injection moulding ready and include internal layouts for PCB, speaker, and silicone rubber buttons. Requirements: - DFM (Design for Manufacturing) is essential. - Deliverables should include STEP files and production drawings. - Enclosure material: ABS - Finish: Matte - Buttons: Silicone rubber buttons Ideal Skills and Experience: - Experience in consumer electronics design - Proficient in creating DFM-ready designs - Strong knowledge of injection moulding processes - Expertise in producing detailed STEP files and production drawings Please share relevant portfolios with your bids.

...firewall/console, allowing us to decommission our Windows-based Active Directory while maintaining secure, role-based access to our network resources. Scope of Work: UniFi Identity Setup: Configure UniFi Identity (UID) on our UniFi Cloud Gateway. User Migration/Creation: Assist in migrating existing users or setting up a new user directory within UniFi Identity. Authentication Replacement: Set up One-Click WiFi (Radius-less or WPA-Enterprise) using UniFi Identity credentials. Set up One-Click VPN (WireGuard or L2TP) for remote staff, replacing AD-integrated VPNs. Role-Based Access (RBAC): Configure Groups and Roles to ensure users only have access to specific VLANs or resources based on their department. Device Integration: Ensure Windows/macOS endpoints can connect to the net...

...Reservation overview • Profile settings • Cancel / modify if allowed 6. Admin Panel • Host management • User management • Bookings management • Content moderation 3.2 Extensive Features — FULL-FLEDGED PLATFORM 1. Review System • 1–5 stars + text • Optional: host can also review tenant 2. Advanced Search & Filters • Map view (Leaflet or Mapbox) • Filters: sauna, hot tub, eco, forest, water, wifi, etc. 3. Dynamic Pricing • Weekend rates • High season • Adjustable rules 4. Messaging System • Real-time chat (WebSockets / ) • Push notifications 5. Multilingual • NL / FR / DE / EN via i18n routing 6. iCal Sync with Airbnb / Booking • Automatic calendar import/export 4. ARCH...

...management** for deployed systems (focus on commercial available platforms) The focus of this project is the **base platform and system enablement**. Application-level dashboards or advanced UI development are **explicitly out of scope**. --- ## 3. System Architecture Overview ### 3.1 Hardware Platform - Custom-designed hardware (already functional) - Raspberry Pi Compute Module 4 - Ethernet and WiFi connectivity - Industrial-grade SD memory card 32MB with memory controller (or higher capacity if needed) **Important requirement:** The software architecture must **minimize or eliminate write cycles to the SD card** to significantly extend SD card lifetime (read-only root file system, RAM-based logging, or equivalent strategies). --- ## 4. Hardware Components and Periph...

...level number (e.g., the video for level 233 should be named ). - Video Quality: Clear, high-quality gameplay recordings (minimum 720p resolution, smooth frame rate). - Delivery Schedule: Submit Minimum 40 videos daily via a Google Drive link. This is mandatory. - Game link - - You need 5G mobile or Wifi to send daily 40 or more videos(because sending 40 video will require more than 5GB data) NOTE - To deliver daily 40 level solving videos, you have to spend atleast 5 hours a day on playing game. Budget: Total Budget: ₹2000 for all 1000 videos. Initial deposit: ₹500 (to be paid upon project acceptance). Remaining payment will be released upon successful completion and delivery

I need help connecting my already installed wired security cameras to my WiFi router at home. Ideal Skills and Experience: - Experience with wired security camera systems - Knowledge of WiFi network setup and configuration - Ability to troubleshoot connectivity issues - Prior work with home security systems is a plus

UK Part-time Recruitment | WiFi Field Data Collector, Earn Extra Money Easily! Core Highlights • Transparent Salary: 3gbp per asset, more work more gain, no hidden deductions • Flexible Time: No office hours required, take orders and arrange your time freely in spare moments • Ultra-low Threshold: No professional experience needed, easy to master for beginners, with bilingual (Chinese & English) operation manual • UK-wide Coverage: No specific city restrictions, available anywhere in the UK Must-Meet Requirements (All Required) 1. Location Requirement: Must be located in the UK and able to complete on-site data collection tasks locally 2. Device Requirement: • Android smartphone (Android 6.0 or above; Android 9.0 is not recommended as it tends ...

UK Part-time Recruitment | WiFi Field Data Collector, Earn Extra Money Easily! Core Highlights • Transparent Salary: 3gbp per asset, more work more gain, no hidden deductions • Flexible Time: No office hours required, take orders and arrange your time freely in spare moments • Ultra-low Threshold: No professional experience needed, easy to master for beginners, with bilingual (Chinese & English) operation manual • UK-wide Coverage: No specific city restrictions, available anywhere in the UK Must-Meet Requirements (All Required) 1. Location Requirement: Must be located in the UK and able to complete on-site data collection tasks locally 2. Device Requirement: • Android smartphone (Android 6.0 or above; Android 9.0 is not recommended as it ten...

...and interfaces with multiple sensors for two separate hives. The device will be powered by a Solar panel and a Li-Ion/LiFePO4 battery. Core Components & Requirements: Microcontroller & Connectivity: Based on ESP32 with LoRaWAN capabilities. Preference: You can either design around a module (like ESP32-WROOM + RFM95) OR design a carrier board for a dev-board like the Heltec WiFi LoRa 32 V3 (to simplify assembly). Please specify your recommendation in your proposal. Sensors (Interfaces needed for 2 Hives): Weight: 2x Interfaces for Load Cells (4-wire). The PCB must integrate 2x HX711 ADC chips directly (or provide headers for breakout boards, though integrated chips are preferred for reliability). Audio: 2x Interfaces for exter...

ATLANTIS OTA UPDATE SYSTEM – DEV PROMPT (WIFI TEST FIRMWARE) Objective Implement a production-grade OTA firmware update system for Atlantis controllers that is safe, rollback-capable, power-loss tolerant, and integrates with Blynk NCP (ESP32 runs unmodified NCP firmware). Deliver test firmware that validates the entire OTA lifecycle over Wi-Fi before Blynk integration. System Overview Hardware Primary MCU: STM32H723VIT6 (main firmware; Arduino sketch runtime) Connectivity MCU: ESP32 running Blynk NCP binary (not modifiable) Dealer flashing: Android Dealer Toolkit via USB-C UART, toggling BOOT0 + NRST, using STM32 ROM bootloader Dealer flashing is force-install / recovery Dealer flashing does NOT interact with running firmware Dealer flashing does NOT write OTA metadata Non-Ne...

...to be intermittent resulting in some incomplete calculations. I need logic that decides, on the fly, which detection wins when classes conflict—whether that means tweaking NMS thresholds, adding a class-confidence hierarchy, or inserting a lightweight post-processor in Python/C++ that still keeps frame-rate latency low. 2. Flutter connection hiccups The mobile app fails to connect to the WiFi hotspot or drops its link to the snippets/concatenated videos. A rock-solid fix that works across iOS and Android is required so a user can tap once and reliably receive either a single clip or a stitched highlight. Immediate deliverables • Implement and benchmark an object-priority solution inside the existing YOLO workflow. • Patch the Flutter download pipeline ...

I need a highly detailed 3D model of an arena for a new WiFi design presentation. The model should include: - Seating arrangements - Hospitality areas - Internal and external concourses I have both floor plans and reference images to assist. Ideal Skills and Experience: - Proficiency in 3D modeling software - Experience with high-detail architectural designs - Ability to work quickly and meet tight deadlines I also need this ASAP for an upcoming presentation with the client. Looking forward to your bids!

My spare MacBook has suddenly stopped seeing any wireless networks, even though the other computer on the same desk is happily online. I’m on macOS and, so far, the affected machine can’t detect a single network—home, hotspot, or neighbour—so it’s not just my router. What I need from you is a real-time remote session (Zoom, TeamViewer, or your preferred secure tool) to: • diagnose why the Wi-Fi interface is blind • walk me through any Terminal commands, SMC/PRAM resets, or network-interface reinstalls required • verify that the Mac can once again scan, join, and hold a stable connection I’ll stay on the working computer throughout our session for screen sharing and chat, and I can reboot the faulty Mac as many times as needed. ...

I have an Ubuntu-based box with two physical interfaces: the wired port will face a public network, while the built-in Wi-Fi card (or any other you advise) will broadcast a private hotspot. I need that machine to behave as my main router, tunnelling every outgoing connection through a VPN so users on the Wi-Fi side enjoy secure browsing at all times. Here is what I expect: • The LAN interface pulls DHCP from the public line and forwards nothing until the VPN is up. • The Wi-Fi interface advertises an SSID of my choice, hands out local addresses, and transparently pushes all traffic through the VPN tunnel (OpenVPN or WireGuard—whichever you feel delivers greater stability). • NAT, DNS, and firewall rules must be configured so clients connect instantly without e...

...build a custom website for one short-term rental property. The site should support direct bookings, payments, guest automation, and Airbnb/VRBO calendar syncing. Key Requirements: Standalone, mobile-friendly website for a single STR Direct booking on the site with secure payment processing Two-way calendar sync with Airbnb and VRBO Guest login/accounts Guest login required to access house WiFi Automated guest emails (pre-arrival, during stay, post-stay) Guest Shopping Feature: “Shop the House” section Ability to link items used in the home (sheets, mattresses, art, décor, etc.) Simple setup — affiliate links or direct checkout (open to recommendations) Admin Needs: Easy dashboard to manage bookings, guests, emails, and products Ability to up...

... If someone could even do this pro bono, I’d advocate and advertise your services on each page of my site. *customers must pay before service is provided- service is free delivery and pick up, clear categorized bags upon delivery so the client can just take 2 minutes to put away. - unsure if I should charge per bag of laundry or pound, if per pound I’d like to charge $1.95 a pound. I have a WiFi scale so the customer wouldnt ever be overcharged unexpected charges. We offer full service wash dry and meticulously folded professionally folded laundry. I need this website desperately to support my daughter by myself and keep our home. Her. Birthday is next Month. I’d be willing to give all of the gift cards I have for some help or someone to pay it forward. ...

...already have 4 domains which ill have to direct to a single website. Key details you should know: • Primary focus: BNB-style lodging (not a general e-commerce or portfolio site). • Accommodation type: whole property rental. • Must-highlight amenities: reliable WiFi and a fully equipped kitchen. What I need built: – A clean, mobile-responsive site with an attractive homepage, an availability/booking calendar, rate management, and instant confirmation email workflow. – Photo gallery and amenity section that emphasises WiFi and kitchen access. – FAQ/contact page with a Google Maps embed. – Basic on-page SEO and SSL setup so the site launches ready for search and secure browsing. Acceptance criteria: 1. Guests can search date...

I already run a CData TR-069 server and have a basic companion app, but it still asks end-users to type the server IP every time. I need a fresh Android build where the endpoint is hard-coded in the codebase, not exposed to the user. Core functions I must keep: • Show every active client currently associated with the router, refreshing in near real-time. • Let the user change the WiFi SSID password from within the app (the change has to flow through the existing TR-069 calls). • Display per-client device details—MAC, hostname and connection type—plus simple network-usage figures such as current throughput or total bytes. I want a custom UI that follows my brand colours rather than the look of the existing demo app. Material-you components are fin...

I have a complete CAD file that shows our structured cabling, CCTV, WiFi, access-control and biometric system layout. What I need now is a clean, construction-ready shop drawing set along with a matching schematic diagram. The CAD base will be provided to you; your task is to extract the low-voltage information and present it in a way that the installers can follow without guessing. The drawing package must clearly illustrate device locations, cable routes, and terminations for the three critical subsystems we rely on—CCTV, WiFi and Access control—while staying faithful to the original CAD coordinates. Layer management, consistent line weights, and a concise legend are essential so the prints read well both on-screen and on paper. Deliverables • Updated DWG...

...auxiliary lights turn on automatically. If we additionally activate the right turn signal indicator, the right auxiliary light will turn off so that the turn signal has more prominence and oncoming drivers can better identify the action the motorcycle is about to make. Elements to Use: This is the part where I hope you can help me. We will use an ESP32 microcontroller. I would like it to have WiFi and Bluetooth, with a good amount of memory since it will have a web server running (for configuring the lights as the client needs) The system will have 6 output lines (15A lights, charging USB, rear light, etc.) Each line will be controlled by D4184 MOSFETs in parallel. It's important that the MOSFETs can operate with PWM so we can dim the lights as needed For every 2 channels ...

...blueprint for a small tracker that can be fastened to any asset and determine its position inside a building by scanning nearby WiFi access points. Every 15-30 minutes (configurable) the unit must wake, calculate its coordinates, and post them to my cloud back-end. A single push-button on the device serves as a service call: when pressed it must instantly trigger two actions—send an email alert and push a notification to our web dashboard through a REST or MQTT endpoint. I am looking for a document set that details: • Hardware architecture: MCU, low-power WiFi module, antenna, sensor package, power source, and enclosure considerations • Firmware flowcharts covering WiFi scanning, interval sleep strategy, and button interrupt handling • ...

The goal is to create a straightforward Android application that pairs with my ESP32-based smart bait boat over both WiFi and Bluetooth. From a single screen I want to steer the boat with an on–screen joystick, trigger preset bait-container positions (Half Open, Fully Open, etc.), adjust speed and other numeric parameters, and view a small live GPS mini-map. I will supply the ESP32 firmware protocol; your task is the Android side. Please build the project in Android Studio (Kotlin or Java is fine) and keep your code modular so I can extend it later. ESP-Now, classic Bluetooth, or BLE can be used under the hood as long as the boat can be discovered, paired, and commanded reliably. Deliverables • Compiled APK demonstrating all features with my test boat • Complet...

...to lighting schedule; pot lights; feature lights; exterior; multi-level lighting (not just ceiling) D3 Smart switching plan: 3-way/4-way where needed; switch locations + what they control (smart connected) D4 RCP (if ceilings change): ceiling types/drops/bulkheads/soffits + lighting placement D5 Panel schedule + load notes (if upgraded): panel capacity, circuits, legend D6 Low voltage plan: data, WiFi AP locations, cameras, speakers, doorbell E) MECHANICAL / HVAC — IFC READY E1 HVAC design basis + equipment schedule: furnace/heat pump model assumptions; HRV/ERV if included E2 Ducting plan (all levels) supply+return (MANDATORY — current home has NO ducting): runs, sizes, diffusers, returns E3 Mechanical room layout: clearances, service access, drain/vent coordination ...

...General WordPress (latest stable version) Clean, scalable, well-structured code Fully responsive (mobile-first) High performance and security best practices 2) Front-End Features Homepage with advanced hero search (location, dates, guests) Custom villa search & filtering system: Location hierarchy (country → region → place) Number of guests Price range Bedrooms / bathrooms Pool options Amenities (WiFi, air conditioning, pets allowed, sea view, etc.) Search results page with sorting options SEO-optimized location landing pages Villa detail pages with: Image gallery Description & highlights Amenities Pricing & availability Inquiry / booking request form Contact & inquiry flow with email notifications Legal pages (privacy policy, terms, cookies) 3) Multil...

...overseas worker who knows what it means to be cut off from both family and a stable signal. Back home, many remote villages still have no mobile coverage, and countless abandoned elders and young families sleep on the streets. I want to address both problems in one coordinated project. Phase 1 – Stronger Signal for Remote Villages • Scope: Boost coverage through cell-tower enhancement (not WiFi hotspots or satellite). • What I need: a complete technical plan—site surveys, optimal tower locations, regulatory checklist with the NTC/LGUs, bill of materials, rollout timeline, and basic costing that local crews can follow. Phase 2 – Permanent Homes for the Homeless • Scope: Design and implementation plan for durable, low-cost, typhoon-resis...

...to ASA. The format will be live screen sharing with recording preferred. The session should include real-world use cases and a Q&A session. Deliverables 30-60 minute technical session Live screen sharing Recording of the session Q&A session Real-world use cases The training is expected to follow this logical flow: Design & preparation – Network segmentation (Inside / Outside / DMZ / Server / WiFi) – NGFW core concepts (ACP vs ACL, NAT, routing, VPN, IPS, AMP, URL filtering) Environment & FMC preparation – Firepower 3120 readiness – FMC role, workflow, and management concepts Base configuration – Adding NGFW to FMC – System settings (IP, routing, NTP, SNMP, Syslog) – Initial security policy activation Security ...

Before question, Please read the following absolutely. [ Output ] Schematic and Artwork PCB file of Kicad 8.0 [ Description ] Additionally, add TP4056 Module to charge 18650 1S battery and 18650 Single Battery Holder (PCB Type). [ Main Parts and Datasheet ] 1. ESP32-C5 Module : 2. Color 320x240 Touchscreen, 2.8 inch, ILI9341 Controller 3. TP4056 : Battery Charging Module

My home Wi-Fi was recently breached and I can still see unfamiliar devices connecting even after I changed the password. I need an experienced network-security freelancer who can jump in remotely, pinpoint how the unauthorized access is happening, and lock the network down for good. Here’s what I expect: • Run a quick audit of my existing router settings, logs, and connected clients to confirm the intrusion vectors. • Reconfigure the router with stronger protections—WPA3 where available, hidden SSID if practical, MAC filtering, upgraded firewall rules, and a properly segmented guest network. • Verify and, if necessary, update firmware, disable insecure services (WPS, UPnP, weak remote-admin ports), and adjust DNS or VPN settings to shield traffic. •...

ESP32-S3 Multi-Axis Motion Control System with WiFi Interface and I2C Expansion