Altium Designer Jobs

I need a double-layer, signal-processing board laid out in Altium Designer and prepared for fabrication at JLCPCB. The finished board will fit inside a 15 cm × 15 cm envelope, so component placement, routing, and keep-outs should respect that medium-size constraint. Deliverables I expect: • Complete Altium project with schematics and PCB layout • Optimised Gerber, drill, and pick-and-place files matched to JLCPCB’s specs • BOM with manufacturer part numbers and assembly notes I will review the design by importing the files directly into Altium and running JLCPCB’s online DFM check; the job is complete once the files upload without errors and the board passes ERC/DRC.

Who Should Apply Please apply only if you have direct experience in electrical symbol creation, library development, or related automation systems. This project requires more than general coding ability. Preference will be given to freelancers who can demonstrate a clear understanding of the requirement and prior implementation experience in this area. Project Overview I am looking for an experienced freelancer to develop an AI-assisted electrical schematic symbol automation tool with a strong focus on accuracy, structured symbol generation, editing flexibility, and multi-EDA export support. Core Concept The main concept of this project is as follows: A user will open a component datasheet from a website, PDF, browser, or any other source. The user should be able to capture the pin d...

The original schematics and firmware sources for my existing motherboard are no longer available, yet I still need to keep the product alive and solve a series of recurring hardware failures. The immediate objective is to reverse-engineer the board in detail so I have a complete, accurate picture of how every power rail, I/O interface, and embedded controller is wired and programmed. Once that knowledge is captured, I want a refreshed design that removes today’s failure points and is ready for a short production run. Work starts with non-destructive teardown, high-resolution imaging, net tracing, and firmware dumping via JTAG/SWD or any other proven technique. From there the task moves into schematic recreation (Altium Designer or KiCad preferred), BOM generation with current compon...

I’m building a small-footprint PCB around the ESP32 that will serve as the core of several IoT devices. The board must expose reliable Wi-Fi, Bluetooth, and flexible sensor headers so it can drop straight into prototypes and low-volume production runs. Here is the scope I have in mind: • Schematic capture for the ESP32 module with stable power-management, antenna clearance, and USB-to-UART programming interface. • PCB layout (2-layer is fine if performance allows) that remains within 50 × 50 mm, ready for standard SMT assembly. • Breakouts or onboard footprints for common environmental sensors; I haven’t finalised the exact parts, so leave room on I²C and a couple of ADC/GPIO lines for temperature, humidity or motion modules. • Production...

We are developing a carwash kiosk control board that will work together with our Paymore TPOS device, and we are looking for an experienced embedded hardware designer to design a production-ready PCB. This is a real commercial product that will go into mass production, therefore the design must be industrial-grade and manufacturable. The board will control a P10 LED panel (HUB75) that runs continuously 24/7, displaying countdown timers and simple messages. The system must also include Pulse+ and Pulse− inputs that can operate either as dry contact inputs or opto-isolated inputs, counting pulses and triggering system actions. Based on the detected pulses, the board must activate one of 10 independent output channels that can drive 5V or 24V signals for a defined period and then autom...

Freelance Hardware Engineer – Altium PCB Design Review (Remote Access) We have an existing Pulse Converter PCB designed using Altium Designer and are looking for an experienced freelance hardware / PCB design engineer to perform a technical design review. The work will be done via remote access to our computer (AnyDesk / TeamViewer). Design files will not be shared. Detailed circuit functionality and design context will be explained after mutual agreement and confidentiality alignment. Scope of Work: Review the schematic and PCB layout in Altium Designer and identify potential design issues, risks, and improvement points, including but not limited to: Power input and regulation (wide-range DC input) Relay driver circuits Optocoupler-based pulse input circuits MCU (ESP32 or sim...

I am building a tiny GPS tracker device for my company and need an experienced PCB designer. Project Requirements: - Design schematic and PCB layout for a compact GPS tracker. - Use SIM7080G (LTE/NB-IoT with GNSS) module. - Include SIM card slot, GPS antenna connector, LiPo battery connector, and charging circuit. - Board size should be approximately 18 mm x 20 mm. Deliverables: - Complete schematic - PCB layout - Gerber files for manufacturing - Bill of Materials (BOM) - Pick and Place file (optional) Preferred Tools: KiCad, Altium Designer, or EasyEDA. Experience Required: - Experience designing IoT or GPS tracking devices - Knowledge of RF layout and antenna placement Budget: $30 – $50 (negotiable) Please share examples of previous PCB designs.

I will provide the full Proteus project (schematic, PCB, libraries). Your task is to recreate that board in Altium Designer as an exact, bit-for-bit copy—same dimensions, traces, footprints and reference designators—so the migrated file can drop-in-replace the original. Once the design lives in Altium, prepare a complete production package for JLCPCB consisting of: • Gerber set generated with Altium’s CAM outputs • Pick-and-place centroid file (CSV) referenced to the board origin JLCPCB expects • Clean BOM that matches the Altium project and includes LCSC part numbers and JLCPCB’s preferred column headings Please keep the design locked as-is; no routing or placement tweaks. Organise the schematic sheets and PCB libraries so I can add compo...