
Closed
Posted
Paid on delivery
# BMW CAS3+ CAN Bus Ignition & Engine Cranking — Feasibility Investigation I'm looking for someone experienced in BMW electronics, automotive CAN bus communication, and firmware reverse engineering. **Vehicle:** BMW E61 520d LCI (2009), manual transmission, original CAS3+ module. **My objective:** I want to determine whether it is possible to send a CAN bus message (or an authorized sequence of messages) to the original CAS3+ module to: 1. Turn on ignition (KL15). 2. Initiate engine cranking (KL50). 3. Use the original BMW key positioned near the key-reader coil. 4. Retain the original immobilizer, genuine-key authentication, and factory safety interlocks. **Important:** I am not looking to replace the CAS module, bypass the immobilizer, or install an aftermarket remote-start system. I only want to establish whether this functionality is supported by the stock CAS3+ firmware. **Research already available:** I can provide the original CAS3+ firmware image, Ghidra decompilation, CAN ID analysis, and extensive technical findings from previous investigations. Remote-start-related CAN processing has already been identified, including CAN ID `0x282`, but no complete ignition-activation path has been verified. **What I need from you:** Analyze the existing research and determine whether an original, authenticated CAN-controlled ignition and cranking path exists. Explain the required hardware, software, key-authorization, and safety conditions, and provide supporting technical evidence. If it is not possible with the available firmware and configuration, explain the specific limitation. **Budget:** €50–€100 Please apply only if you have relevant experience with BMW CAS modules, Freescale/NXP HCS12X processors, Ghidra/IDA, or automotive embedded systems.
Project ID: 40803157
54 proposals
Remote project
Active 4 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
54 freelancers are bidding on average €127 EUR for this job

Hi, I am an embedded systems engineer with over 16 years of experience. I have extensive experience with automotive CAN communication and embedded firmware analysis, including reverse engineering with Ghidra. I can review your CAS3+ firmware and existing research to determine whether the stock firmware supports an authenticated CAN path to KL15 activation and KL50 cranking. Your findings around 0x282 provide a useful starting point, though the complete authorization and activation path needs to be established. I will provide a concise feasibility report with supporting firmware references, required hardware and software conditions, and the genuine-key authentication and factory safety prerequisites. If the firmware or configuration prevents this functionality, I will explain the specific limitation. I will also flag any findings that require bench or vehicle confirmation. My €100 bid covers a focused investigation using the material you already have. Do you have access to the vehicle or a CAS bench setup for validation if needed? Please contact me to discuss details.
€100 EUR in 5 days
7.6
7.6

I’ll analyze your CAS3+ firmware and existing CAN findings to trace whether KL15 and KL50 can be triggered by an authenticated CAN sequence while preserving the original key challenge-response and immobilizer interlocks. My approach is to map the CAS3+ CAN handler around 0x282, verify the key-authentication state machine, and confirm whether the firmware exposes a legitimate ignition/cranking path or hard-blocks it outside the factory key-reader sequence. If the path exists, I’ll document the exact hardware, software, and safety conditions required; if not, I’ll identify the specific firmware limitation that prevents it.
€250 EUR in 7 days
5.9
5.9

Hello, My 10+ years in embedded electronics, industrial control systems, and hardware troubleshooting give me a strong foundation for investigating the CAS3+ ignition and cranking architecture. I understand how controllers, relays, safety interlocks, sensors, and communication interfaces interact in real machines, which is directly relevant to evaluating whether a CAN request can produce an authorized KL15/KL50 action. I can examine the provided firmware research and Ghidra findings from an electronics and embedded-systems perspective, trace the relationship between CAN processing, authentication conditions, outputs, and safety states, and distinguish a genuine stock-firmware capability from a message that is only detected but cannot complete the ignition path. My experience with microcontrollers, digital electronics, troubleshooting, and system integration also supports assessing the required interfaces and hardware conditions without claiming an immobilizer bypass. I would be glad to analyze the available evidence and provide a technically grounded feasibility conclusion, including the specific limitation if the original CAS3+ configuration does not support this function. Thanks!
€180 EUR in 5 days
5.6
5.6

Hi, I have experience with automotive embedded systems, firmware reverse engineering, CAN bus communication, and Ghidra analysis. I can investigate your original BMW CAS3+ firmware, trace the CAN ID 0x282 processing path, and examine the KL15/KL50 control logic and factory authorization checks. My goal will be to determine whether the original firmware supports authenticated ignition and cranking without bypassing the immobilizer or factory safety systems. I'm available to review your existing research and provide a clear technical feasibility report.
€30 EUR in 1 day
6.0
6.0

My embedded-systems and firmware background is directly relevant to evaluating a CAN-controlled ignition path without altering the original CAS3+ hardware. I specialize in microcontrollers, embedded C/C++, reverse engineering, and automotive-style electronic systems, with experience analyzing firmware behavior and documenting hardware/software interactions. I can assess the supplied Ghidra decompilation, CAN ID findings, and firmware image for evidence of authenticated KL15/KL50 handling, message validation, state machines, key authorization, and safety interlocks. My electronics and microcontroller knowledge also supports evaluating the required CAN interface, CAS connections, key-reader conditions, and whether the stock HCS12X-based firmware exposes a genuine authorized path or only processes unrelated remote-start traffic such as 0x282. I will provide a technically grounded feasibility report identifying supporting code paths, dependencies, and any firmware or configuration limitation, while keeping the original immobilizer and factory security model central to the analysis. I am well suited to investigate this firmware and CAN question.
€140 EUR in 7 days
5.5
5.5

Hi, how are you doing? I went through your project description and I can help you in your project. your project requirements perfectly match my expertise. We are a team of Electrical and Electronics engineers, we have successfully completed 1000+ Projects for multiple regular clients from OMAN, UK, USA, Australia, Canada, France, Germany, Lebanon and many other countries. We are providing our services in following areas: Antenna Design (CST, HFSS) Embedded C Programming. VHDL/Verilog, Quartus/Vivado, LabVIEW/ Multisim/PSPICE/VLSI MATLAB/SIMULINK Network Simulator NS2/NS3 Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC, STM32 and ESP32. IDEs like Keil MDK V5, ATmel studio and MPLab XC8. PLCs / SCADA PCB Designing Proteus, Eagle, KiCAD and Altium IOT Technologies like Ethernet, GSM GPRS. HTTP Restful APIs connection for IOT Communications. Also, we have good command over report writing, I can show you many samples of our previous reports. Kindly consider us for your project and text me so that we can further discuss specifically about your project's main goals and requirements.
€140 EUR in 7 days
6.2
6.2

I can assess whether the stock BMW CAS3+ firmware supports an authenticated CAN-controlled KL15/KL50 path while preserving the original key authorization and factory interlocks. My approach would correlate your 0x282 findings with HCS12X firmware control flow, CAN reception and dispatch logic, state machines, immobilizer authorization checks, terminal-control routines, and the conditions required before ignition or cranking requests are accepted. I would also review the Ghidra decompilation, firmware image, CAN traces, and module configuration to distinguish a genuine supported path from diagnostic, wake-up, or remote-start-related handling. The deliverable would document the relevant functions, message conditions, authorization dependencies, timing and hardware assumptions, and technical evidence for either a feasible authenticated sequence or a firmware/configuration limitation. Analysis would remain focused on authorized bench research and preserving factory safety mechanisms, not immobilizer bypass or theft-enabling modifications. I can provide a clear feasibility conclusion with annotated findings and recommended validation steps.
€100 EUR in 2 days
5.4
5.4

Embedded firmware and electronics are central to my work, with skills in C programming, microcontrollers, electrical engineering, and firmware development that align with investigating a vehicle module’s CAN-controlled behavior. I can assess the supplied CAS3+ firmware and Ghidra findings at the embedded-code level, trace relevant CAN message handling, and distinguish an actual ignition/cranking command path from diagnostic or remote-start-related processing. My electronics background also supports evaluating the required bus hardware, key-reader interaction, authorization state, and factory interlocks without claiming an immobilizer bypass. Where the stock firmware or vehicle configuration prevents the requested function, I can explain the specific technical limitation and evidence behind it. I would be glad to apply my firmware and automotive-electronics analysis skills to this feasibility investigation and provide a clear, technically grounded conclusion.
€200 EUR in 7 days
5.3
5.3

My electronics and firmware skills provide a foundation for reviewing embedded automotive control logic, but I want to be transparent: my professional background is primarily electrical engineering, power systems, and multidisciplinary M&E design rather than BMW CAS3+ reverse engineering. I can still contribute to a structured technical assessment of the supplied firmware and Ghidra findings using my Electronics, Firmware Development, and Microcontroller skills. The investigation would need to distinguish genuine CAS-authorized KL15/KL50 handling from gateway forwarding, immobilizer authentication, transmission-safety checks, and signals that only support aftermarket remote-start interfaces. I can also document hardware, software, key-presence, and interlock dependencies clearly, while identifying evidence for any firmware or vehicle-configuration limitation. For specialist CAS3+/HCS12X conclusions, my experience should be evaluated carefully against the specific BMW expertise requested. I would be glad to support the embedded-electronics analysis where it matches my capabilities and provide a technically clear feasibility report.
€140 EUR in 7 days
4.8
4.8

Hello, I have experience with automotive embedded systems, ECU communication, and reverse engineering firmware on microcontroller-based platforms. My previous work includes analyzing CAN bus message flows, investigating authentication mechanisms, and tracing firmware execution paths using Ghidra and IDA. Your main challenge is establishing whether the original CAS3+ firmware supports authenticated CAN-triggered KL15 and KL50 activation while preserving EWS security and factory interlocks. I would approach this by examining your firmware, tracing CAN ID 0x282 processing, mapping relevant state transitions, and identifying key-validation and start-authorization dependencies. My focus will be on evidence rather than assumptions, with clear technical findings and an honest feasibility assessment, including any firmware or configuration limitations. I'd be glad to help you establish what the original BMW system can genuinely support. Best regards.
€100 EUR in 3 days
4.6
4.6

My 8+ years in embedded systems and electronics engineering make me well suited to assess the CAS3+ ignition and cranking feasibility at firmware and vehicle-network level. I develop embedded firmware in C/C++, work with microcontrollers, and investigate complex interactions between hardware, signals, and control logic—capabilities directly relevant to reviewing your HCS12X firmware and CAN findings. I can analyze the supplied Ghidra decompilation, CAN ID evidence, and identified `0x282` processing to determine whether an authenticated KL15/KL50 path is actually implemented, including the required key authorization, module states, interlocks, and hardware conditions. My background in signal processing, electrical engineering, troubleshooting, and system integration also supports distinguishing a genuine stock-CAS capability from a message that only triggers auxiliary or remote-start-related handling. I would provide a technically grounded feasibility conclusion with supporting firmware evidence and clearly identify any limitation in the original configuration. I am ready to apply my embedded reverse-engineering and automotive electronics skills to this investigation.
€140 EUR in 5 days
4.4
4.4

Hi there, I see you're looking to investigate the feasibility of sending a CAN bus message to the CAS3+ module of a BMW E61 520d. I have experience with automotive embedded systems, and I'm familiar with BMW electronics, including the specifics of CAN bus communications and firmware analysis using tools like Ghidra. I understand the need to retain the original immobilizer and safety interlocks while exploring ignition activation through authenticated CAN messages. Based on the original CAS3+ firmware image and existing research you’ve provided, I can help analyze and determine the conditions necessary to identify any ignition and engine cranking pathways. Additionally, I’ll outline any limitations if the functionality isn't supported by the existing firmware. If you have any specific requirements or additional details, feel free to share. Regards, Ali
€100 EUR in 1 day
4.4
4.4

Hi, Adelman here from Texas. BMW CAS3+ CAN IGNITION FEASIBILITY - you need proof that the original firmware accepts an authenticated ignition and cranking request without bypassing factory security. I'd approach this as a firmware analysis task, starting with your existing Ghidra findings and tracing CAN ID 0x282 through its message handlers, authorization checks, and KL15/KL50 control paths. I'd map the required conditions and identify where genuine-key authentication and factory safety checks are enforced. The result will be an evidence-based feasibility report, including confirmed paths, missing conditions, and any firmware limitations. I'll keep the investigation within the original immobilizer and safety architecture. Can you provide the firmware image, Ghidra project, and your existing CAN ID analysis so I can assess the current findings? Looking forward to work with you.
€100 EUR in 3 days
4.0
4.0

Hi there, I read your project "BMW CAS3+ CAN Start Feasibility" and it lines up well with my experience in Data Analysis. I've been doing this kind of work for 9 years and focus on clean, well-tested code and clear communication. Before starting I'd like to confirm a couple of details about the scope so the result matches exactly what you need. Happy to jump on a quick chat. I can deliver in 7 days for €250 EUR. Best regards, Siddharth Kasherwal
€250 EUR in 7 days
4.0
4.0

Firmware analysis: Examine the supplied CAS3+ firmware and Ghidra findings, focusing on relevant control paths, state transitions and authorization dependencies. CAN analysis: Review the identified CAN processing, including the reported 0x282 activity, and distinguish message reception from an actual authorized ignition request. Immobilizer and authorization: Assess the documented relationship between genuine-key authentication, CAS authorization, vehicle state and engine-start permission. Feasibility conclusion: Determine what the available evidence confirms, what remains unverified, and whether additional configuration or hardware evidence is required. Technical report: Provide findings, supporting references to the supplied research, limitations and recommended next investigative steps. I would preserve the factory immobilizer and safety architecture. The investigation would focus on determining whether an OEM-authorized path exists, rather than bypassing authentication or modifying security controls. Before starting, I would like to confirm: Is the firmware image read directly from your original CAS3+ module, and is its version/configuration known?
€250 EUR in 7 days
4.0
4.0

Thanks for posting the project. I am happy to work within your proposed budget of €50–€100. I understand that you need a detailed feasibility investigation of the original BMW E61 CAS3+ firmware to determine whether authenticated CAN communication can trigger KL15 ignition and KL50 engine cranking while preserving factory immobilizer and safety protections. With 8 years of relevant engineering and embedded systems experience, I can help analyze your supplied firmware, Ghidra decompilation, CAN ID findings, and existing research. My approach will focus on examining CAN message processing, particularly ID 0x282, tracing relevant firmware routines, and identifying the relationship between key authentication, ignition states, starter authorization, and factory interlocks. I will provide a structured technical report covering the feasibility, supporting code evidence, required hardware and software conditions, and any firmware or configuration limitations. I will focus strictly on the original security and authorization mechanisms without immobilizer bypass. I'd be happy to review your existing findings and discuss the investigation scope. Best Regards, Sidra https://www.freelancer.pk/u/sidratulm20
€70 EUR in 2 days
3.5
3.5

Hey, Just finished a similar feasibility study on a BMW CAS4+ module—analyzed the firmware in Ghidra, mapped the CAN IDs, and verified the ignition‑cranking flow without touching the immobilizer. I’m the perfect fit for your project. With deep experience in automotive CAN bus communication, reverse engineering on Freescale/NXP HCS12X cores, and years of working with BMW CAS firmware, I’ll examine your CAS3+ image, trace the KL15/KL50 paths, and confirm whether the OEM supports authenticated CAN‑controlled ignition. I’ll outline the exact hardware, software, and key‑authorization requirements, and provide clear technical evidence or pinpoint the limitation if it doesn’t exist. Multiple 5‑star reviews on BMW embedded firmware audits back my work. I’d love to hop on a quick call—or even give a free consultation—to discuss your findings. Chris | Lead Developer | Novatech
€140 EUR in 7 days
3.6
3.6

Hi, Melih Here >> "BMW CAS3+ AUTHENTICATED CAN IGNITION FEASIBILITY" - you need to confirm whether the original firmware supports KL15 and KL50 without bypassing factory security. I would trace the identified CAN ID 0x282 through the supplied HCS12X firmware and Ghidra findings, then check the authorization logic, key validation, and safety conditions. The result will clearly distinguish a supported factory function from a firmware or hardware limitation, with evidence from the code. Can you provide the firmware image and existing Ghidra analysis for the initial review? Looking forward to work with you.
€100 EUR in 3 days
3.0
3.0

Hi there, I can support the data-analysis side of your BMW CAS3+ feasibility investigation by examining the firmware, Ghidra decompilation, CAN ID findings, and technical evidence you provide. My profile is centered on software development with 8 years of experience in Python, Node.js, and JavaScript, including building reliable backend systems and working with complex data. For this project, I can help organize and analyze the available findings around CAN ID `0x282`, compare identified message-handling logic with the requested KL15/KL50 behavior, and clearly document whether the stock firmware exposes an authenticated path or where the evidence stops. I will keep the conclusion tied to the supplied firmware and analysis rather than making unsupported claims about immobilizer behavior or safety interlocks. I would be glad to apply my data-analysis and software-engineering background to produce a clear, evidence-based feasibility assessment. Landon.
€80 EUR in 7 days
3.1
3.1

Hi, determining whether the stock CAS3+ can accept an authenticated CAN request without bypassing the immobilizer is the key issue here. The main risk is confusing a remote-start-related CAN handler with an actual CAS authorization path for KL15 and KL50. I’d trace the 0x282 processing through the HCS12X firmware, then map its callers, state checks, rolling or key-authentication dependencies, and outputs toward the terminal-control logic. I’d also separate messages that request a state change from those that only report CAS status, and check whether the manual-transmission, brake, key-coil, and vehicle-state interlocks are enforced inside CAS or by other modules. The conclusion would be evidence-based: supported path, missing prerequisite, or firmware/configuration limitation. My background includes 10+ years as a senior engineer working across firmware-adjacent systems, electronics, CAN data analysis, reverse engineering, and C-based software. Please share the firmware image, Ghidra project, and the existing 0x282 findings so the analysis can start from the strongest evidence. Is the firmware dump confirmed to be read from this exact CAS3+ module, or is it from a different vehicle/configuration?
€30 EUR in 1 day
2.3
2.3

drogenbos, Belgium
Payment method verified
Member since Aug 4, 2019
€50-250 EUR
€8-30 EUR
$250-750 USD
$25-50 USD / hour
$10-30 USD
$10-30 USD
€8-30 EUR
$250-750 USD
$3-10 NZD / hour
$1500-3000 USD
$3000-5000 SGD
€30-250 EUR
₹1500-12500 INR
$15-25 USD / hour
$30-250 USD
$250-750 AUD
$5000-10000 USD
$250-750 USD
$10-30 USD
£20-250 GBP
$250-750 USD
$10-30 USD