İptal Edildi

C Programming access control with pic 16F887

For the project, I need someone to write the PIC access control program and draft the connection scheme for me.

The program must be compatible with MPLAB X IDE v.4.05 and written in the C programming language incl. PICkit 3 In-Circuit Debugger/Programmer.

The code must be entered via the keypad. The data sheet is in the upload files.

The microcontroller must be a 16F887.

The LCD of the PICDEM ™ 2 PLUS DEMONSTRATION BOARD must serve as the output.

If the code has been entered correctly, a relay must switch to simulation.

The program should contain interrupts and timers.

Conditions for the access control:

It must be ensured that it is very unlikely that the door can be opened without knowing a "code" for the opening procedure.

It must also be ensured that if the opening procedure is known by trying, the average time taken to crack the "code" will be at least 1 hour.

The opening signal must reset itself after a correct opening after a specified time has elapsed.

The code must contain at least four digits. The code must be changeable. After entering the wrong code three times, you can only enter it again after a certain time.

Beceriler: C Programlama, Elektronik, Mikrodenetleyici

Daha fazlasını gör: best ide for c programming, best c programming book for beginners, online course for c programming, pic16f877a, pic microcontroller programming, 11 easy steps to programming pic microcontrollers in c pdf, pic programming in c for beginners, pic16f877a programming in c tutorial, micro c programming, pic programming in c pdf, pic programming in c examples, electronics, c programming, microcontroller, getting help for c++ programming, embedded c programming for microcontroller chapter 1, c# programming for beginners, access control system programming india, outsource for c programming, online help for c programming

İşveren Hakkında:
( 1 değerlendirme ) Obernau, Switzerland

Proje NO: #17180110

Bu iş için 9 freelancer ortalamada €99 teklif veriyor


I have long experience with 8-bit , 16-bit and 32-bit micro-controllers. I work with Microchip (PIC) , Atmel (AVR , SAM) , ST (STM) , TI (MSP) and NXP (LPC) micro-controllers. I use KEIL IDE , Atmel Studio , Code Compo Daha Fazla

€34 EUR in 3 gün içinde
(33 Değerlendirme)

I understand about your requirements. I have good programming experience. I think I can do your work perfectly. If you choose me, I will finish it in time and do my best. I will provide you one month bug free suppo Daha Fazla

€100 EUR in 3 gün içinde
(27 Değerlendirme)
€100 EUR in 3 gün içinde
(19 Değerlendirme)

*******************EXPERT IN pic16f877***************** Hi! I am interested in your project.I am an expert in Control engineering and microprocessor and have a lot of experiences in the [login to view URL] you give me this proj Daha Fazla

€155 EUR in 3 gün içinde
(6 Değerlendirme)

Hi, i have worked on similar project on freelancer. you may go through pr check my ID and its reviews or past done project, portfolio. Thank you

€100 EUR in 3 gün içinde
(4 Değerlendirme)

am Mohamed Hafz the representative of EmbedX Team, EmbedX is a freelancing team that provide wide range of services including: - Embedded systems design - IOT applications and related cloud services - Prototyping Daha Fazla

€88 EUR in 4 gün içinde
(8 Değerlendirme)

Dear sir. I'm a C expert, and have 5 years of experience in embedded programming. I already read your project details. I want to help you than needed the money. I hope to work with you. Then I will give you satisf Daha Fazla

€70 EUR in 3 gün içinde
(1 Yorum)

How are you? I have many experiences about pic programing. I have used almost PIC`s functions, will simulate in proteus and complete in time.

€200 EUR in 3 gün içinde
(2 Değerlendirme)

I have 2+ years of exeperiance as an embedded [login to view URL] worked on pic16/pic18/pic24 controllers.

€45 EUR in 10 gün içinde
(6 Değerlendirme)