İptal Edildi

Electrical and PCB design: An ultra low power RF receiver

In 2011, researchers have shown a design of an ultra low RF wake-up receiver (PDF attached). The PDF contains references to other low power receiver designs.

The job is to create a module (schematics, PCB layout, and PCB) using this or a similar design and containing a 2.4GHz transceiver including a printed antenna, as well as a microcontroller.

(1) The following power consumption targets must be achieved:

a) <50uW (microwatts) in "rx-sleep" mode. This is the default mode.

b) <50mW (milliwatts) in full operating mode (MCU awake and transmitting data)

(2) Further specs of the module must be met:

a) The module wakes up from rx-sleep mode as soon as a specific preamble including a matching device id is sent to the 2.4GHz transceiver. This also means that the module needs a memory for storing a unique ID.

b) The change from rx-sleep to full operating mode must take no longer than 250ms.

c) Power source of the board: 3V LIPO powered, no external stabilizer.

d) Transceiver speed in full operating mode: >=9.6KBit/s.

e) Transceiver sensitivity/power in rx-sleep and in full operating mode must be such that a reliable indoor range of 25m is achieved @2.4KBit/s.

f) MCU provides at least 20KByte of program space, four digital inputs/outputs (3.3V), and two analog inputs/outputs (PCM). MCU clock rate is at least 128KHz, preferably without a separate crystal.

g) The PCB dimensions must be smaller than 3*3cm (smaller is better). The PCB may be double sided / two layers.

h) The PCB silkscreen layer must contain a note to the manufacturer that the antenna section of the board is sensitive to added copper.

(3) Data files and ownership:

a) The schematics and PCB layout are to be provided in an editable format (EAGLE prefered).

b) In addition, the exact data needed for manufacturing is to be provided, such as BOM, dialectric thickness, trace thickness/width, relative permittivity, characteristic impedance, and any other relevant data.

c) Ownership of the module and all data created as part of this job is transferred to the buyer. Information is not shared with third parties, unless agreed with the buyer.

(4) Prototype:

a) In addition to the above, six functioning PCB (looks-like/works-like) prototypes are to be provided to prove that the modules work as intended.

b) A short program demonstrating the functionality of the boards must be provided, for the sender and receiver each.

Beceriler: Elektrik Mühendisliği, Elektronik, PCB Düzen, Kablosuz

Daha fazlasını gör: power up program, power up 2, power part 2, microcontroller prototype, microcontroller job, g works design, electrical design work, eagle 9, design boards, clock design, low cost power supply pcb design, regulated power supply pcb design, power led array pcb design, project power supply pcb design, pcb design power supply, pcb design circuit power supply, pcb design regulated power supply, sample pcb design power supply, power supply pcb design, pcb design volt power supply

İşveren Hakkında:
( 16 değerlendirme ) Stuttgart, Germany

Proje NO: #10252022

Bu iş için 11 freelancer ortalamada €7685 teklif veriyor

mechatronicsengr

Hi, I have experience with ESP8266 and MSP430 Microcontroller. I can execute this project. I would like to discuss few things. Looking Forward,

€6315 EUR in 20 gün içinde
(32 Değerlendirme)
6.0
€11111 EUR in 30 gün içinde
(62 Değerlendirme)
5.9
tkousar

Hi, I am an Electrical Engineer practicing for last 10 years in an R&D Organization. I have designed a number of products ranging from RF & Microwave circuits to digital circuits. i have experience in designing fil Daha Fazla

€5000 EUR in 60 gün içinde
(31 Değerlendirme)
5.9
CoherentTech123

Hello Dear, Glad to see your Job! We are a team of experts with a cumulative experience of more than 50 years in the field of embedded systems, programming, electronics and Prototype development. We offer s Daha Fazla

€5000 EUR in 45 gün içinde
(37 Değerlendirme)
5.7
bandrey

Hello, I have a lot of experience in designing low-power RF modules. In most cases, I use SoCs by Texas Instruments. Example of my work: [login to view URL] https://ww Daha Fazla

€8333 EUR in 90 gün içinde
(2 Değerlendirme)
3.1
electronicproyec

developer of electronic prototypes Hi, I'm, I have worked with many RF modules, (which is needed calculations to suit the pcb) I've seen the attached pdf documentation and everything you mentioned, we can talk ab Daha Fazla

€8888 EUR in 50 gün içinde
(2 Değerlendirme)
1.9
bongbong88

Your project is a perfect fit for my experience and abilities. I have read your job carefully and I am sure I am the best candidate for the job. I have extensive experience in developing a wide range of mobile softwa Daha Fazla

€5000 EUR in 30 gün içinde
(0 Değerlendirme)
0.0
€8333 EUR in 30 gün içinde
(0 Değerlendirme)
0.0
wibluho

hi there, I did review for your project, I see you put 2 different reference one from analog transceiver and one for WIfi CHIP with integrated wifi baseband. I designed many RF module I could show you samples if you Daha Fazla

€8333 EUR in 30 gün içinde
(0 Değerlendirme)
0.0
superior5

Hello, I am expert in PCB DESIGN and have done similar project before, would like to help you in this project. Hope to hear back soon, Regards

€9444 EUR in 60 gün içinde
(0 Değerlendirme)
0.0
€8777 EUR in 40 gün içinde
(0 Değerlendirme)
0.0