Devam Ediyor

Design a PCB - both layout and bill of materials - for a USB charger

I am looking to add 2 USB charging outlets to a new product. The PCB will be fitted internally within the product, and needs to fit within the available space. The board dimensions are 115mm x 24mm. The available space for mounted components is somewhat limited and is highlighted in the attached file 'pcb component [url removed, login to view]'. The position of the 2 USB outlets is also shown. There are also 4 small areas of the PCB where the PCB will be mounted to the product, and therefore no components can be positioned here (see file 'pcb [url removed, login to view]').

It is imperative that this USB charger be of a good quality as it will need to pass CE & British Standard (BS) certification by an independent testing organization. Quality components and adequate separation between high voltage & low voltage paths are crucial.

The input to the charger will be 110 - 240VAC (standard mains power). Ideally the power input will be on the right hand side of the PCB.

Output: 2 x USB dedicated charging ports, 5VDC +/- [url removed, login to view], one port at 1A and one port at [url removed, login to view]

The charger should meet 30mW no-load standby power consumption requirement (five-star energy rating).

It should also incorporate a controller with over-current protection and auto restart.

The design needs to be compatible with common smartphones & tablets, including Samsung, Apple, Nokia, LG etc.

I am looking for freelancers with proven knowledge & experience of similar projects. My budget is towards the lower end of the $250-$750 range.

Beceriler: Elektrik Mühendisliği, Elektronik, Mikrodenetleyici, PCB Düzen

Daha fazlasını görün: bill materials charger, should freelancers incorporate, samsung electronics, requirement for freelancers, rating freelancers, protection for freelancers, product design freelancers, paths design, new materials for product design, lg electronics, high end freelancers, hand bill design, freelancers pcb layout, freelancers output, freelancers organization, freelancers for testing, freelancers for looking small projects, freelancers for electronics projects, freelancers certification, design star, design projects for freelancers, design pcb need, component board, by design auto, auto by design

İşveren Hakkında:
( 6 değerlendirme ) Sungai Buloh, Malaysia

Proje NO: #4439091

Seçilen:

GlobalElectronic

Professional PCB designer offer you professional help

4 gün içinde 361$ USD
(3 Değerlendirme)
3.5

12 freelancer bu iş için ortalamada 495$ teklif veriyor

MikroStar

hi, i am an electrical engineer and an embedded system designer. i can help you with this project.

in 45 gün içinde669$ USD
(43 Değerlendirme)
6.4
Engineer85

Hi I am an Electronic Engineer and interested in doing the job. Thanks

in 21 gün içinde528$ USD
(8 Değerlendirme)
5.8
quang102

hello i can help you do that thanks

in 30 gün içinde550$ USD
(16 Değerlendirme)
5.3
betaenergy

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of ha Daha fazlası

in 3 gün içinde525$ USD
(16 Değerlendirme)
4.8
Davelelievre

Hi, I may be able to help you with your project as I have recently implemented a couple of USB charging projects for phones and tablets.

in 10 gün içinde550$ USD
(3 Değerlendirme)
4.3
andypakilaran

Hello, I'm ready for you job, and ready start from right now. Please check PM.

in 10 gün içinde550$ USD
(0 Değerlendirme)
0.0
rahulranjan949

Lets start the work..

in 30 gün içinde500$ USD
(0 Değerlendirme)
0.0
SarimSuhail

I'm a certified Electrical Engineer recently graduated from a top university. I have recently prepared 2 related projects and I can assure about doing this one with ease and quality. Sample is attached.

in 18 gün içinde528$ USD
(0 Değerlendirme)
0.0
rotek

Let's do it!

in 25 gün içinde500$ USD
(0 Değerlendirme)
0.0
antoonio

Hello, I can design it, check my PM. Regards

in 3 gün içinde550$ USD
(0 Değerlendirme)
3.6
EmbeddedMat

I have experience designing USB controller boards with power distribution. I also have good experience in PCB layout and currently have two boards, I finished laying out last week going into production. My understandin Daha fazlası

in 7 gün içinde374$ USD
(0 Değerlendirme)
0.0
dlpcsit

Hi. Dear sir. I have an interest this part. Please see the PM. Thank you.

in 7 gün içinde275$ USD
(0 Değerlendirme)
0.0