Repair the linux (Angstrom) filesystem (ext3) on my gumstix device
$250-750 USD
Tamamlandı
İlan edilme: yaklaşık 6 yıl önce
$250-750 USD
Teslimde ödenir
Hi,
the filesystem on my gumstix device (overo) running Angstrom 2011.03 is broken due to a friends foolishness.
The system was running OK and then a fsck on a mounted filesystem was done:
e2fsck /dev/mmcblk0p2
e2fsck 1.41.14 (22-Dec-2010)
/dev/mmcblk0p2 is mounted.
WARNING!!! The filesystem is mounted. If you continue you ***WILL***
cause ***SEVERE*** filesystem damage.
Do you really want to continue (y/n)? yes
After this the system is not able to boot anymore:
EXT3-fs: barriers not enabled
JBD: Clearing recovery information on journal
mmcblk0: error -110 transferring data, sector 7475208, nr 8, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 7475212
Buffer I/O error on device mmcblk0p2, logical block 918017
lost page write due to I/O error on mmcblk0p2
JBD: I/O error detected when updating journal superblock for mmcblk0p2.
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): warning: ext3_clear_journal_err: Filesystem error recorded from previous mount: IO failure
EXT3-fs (mmcblk0p2): warning: ext3_clear_journal_err: Marking fs in need of filesystem check.
mmcblk0: error -110 transferring data, sector 131072, nr 8, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 131074
Buffer I/O error on device mmcblk0p2, logical block 0
lost page write due to I/O error on mmcblk0p2
EXT3-fs (mmcblk0p2): I/O error while writing superblock
EXT3-fs (mmcblk0p2): warning: mounting fs with errors, running e2fsck is recommended
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing init memory: 196K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
mmcblk0: error -110 transferring data, sector 7475216, nr 80, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 7475219
[...]
Buffer I/O error on device mmcblk0p2, logical block 98852
lost page write due to I/O error on mmcblk0p2
JBD: recovery failed
EXT3-fs (mmcblk0p2): error loading journal
List of all partitions:
1f00 512 mtdblock0 (driver?)
1f01 1792 mtdblock1 (driver?)
1f02 256 mtdblock2 (driver?)
1f03 4096 mtdblock3 (driver?)
1f04 517632 mtdblock4 (driver?)
b300 7772160 mmcblk0 driver: mmcblk
b301 65472 mmcblk0p1 00000000-0000-0000-0000-000000000mmcblk0p1
b302 7706624 mmcblk0p2 00000000-0000-0000-0000-000000000mmcblk0p2
b303 63 mmcblk0p3 00000000-0000-0000-0000-000000000mmcblk0p3
No filesystem could mount root, tried: ext3
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
See the whole problem in the attached file.
I need this work/repair right NOW!
So only bid, If you are able to do the work right now! You will have to use teamviewer to get onto my machine. The gumstix is connected via kermit to this!
Please first check my profile. I know Linux very well. I see your memory corrupted. this sometimes happen sudden ectrical cut or physical damage or high voltage. whatever it's I can rescue and remove bad blocks
$390 USD 1 gün içinde
5,0 (21 değerlendirme)
4,8
4,8
4 freelancers are bidding on average $444 USD for this job
hello,dear. It's my pleasure meeting you. I have read your requirements and I fully went through it. I am confident and I am sure that I can do your project. Please contact me for further discussing. Thanks for your interests..
ProjectName:Repair the linux (Angstrom) filesystem (ext3) on my gumstix device
Relevant Skills: Arduino, Embedded Software, Linux, System Admin,