
Closed
Posted
Paid on delivery
TITLE: Agri-robot data + dashboard: embedded hardware integration and software (phased) DESCRIPTION: ABOUT US we build small electric robots for small farmers in India. They run on battery packs and swap between three attachments: sprayer, crate carrier and weeder. We want to start a field pilot. We want to see, on a dashboard, what each robot is doing in the field, so we can learn how much power each job uses and how well each attachment works. WHAT WE WANT TO SEE All robots (every attachment): - On/working status, location and faults - Power use of the rover battery and the attachment battery, shown separately, with battery level and remaining run time - Hours worked, distance travelled and energy used per task Sprayer: - Litres sprayed per task and per acre, and tank level - Spray flow rate and pump on-time - Area covered - Alerts for low tank, blocked nozzle or pump fault Crate carrier: - Weight carried per trip and total per day - Number of trips and distance per trip Weeder: - Area weeded and hours worked - Motor load and power use - Alerts for jam or overload WHAT WE NEED FROM YOU Take the data from the robot to a dashboard screen. This is the part we want you to design and recommend: - The electronics: which sensors, boards and modules to use for each measurement above, and why - How they are wired and integrated into our robot, including power, protection, and mounting for dust, water and vibration - How data leaves the field (signal is often weak or absent), and what happens when a robot is offline - Where the data is stored, and the dashboard - A parts list with cost per robot, and the monthly running cost for 2 to 3 robots Please give options where there is a real choice, with your recommendation. We will iterate on the dashboard later, so start with a simple, working version. PHASES (each paid after we test it on our robot) Phase 1 (2 to 3 weeks): power use of the rover battery and the attachment battery on a basic dashboard, so we can compare power use across attachments. Later phases (sprayer, carrier, weeder, then handover) are agreed after Phase 1 is accepted. Target: a working basic version in 1-2 months. WHAT WE ALREADY HAVE - A basic prototype that reads battery data and shows it on a dashboard. Reuse it or replace it. - Two separate lithium battery sets, one for the rover and one for the attachment. Each has its own intelligent BMS (battery management system). - Each battery a.60V and b. 29v brings out four communication wires: CAN (CAN H, CAN L) and RS485 (A, B), plus power on an XT90 connector. (UART might also be available in near future). - BMS make and model: [add here]. We will share the protocol document after an NDA. Please tell us which port (CAN or RS485) you would use to read the battery data, and why. MUST HAVE Experience in both embedded hardware and software/cloud, and with field systems on poor connectivity. You may be a single freelancer or a team. Agriculture experience is a plus. OWNERSHIP We own all code, designs and data. Code goes to our repository from day one, with handover documentation. IN YOUR PROPOSAL, TELL US 1. Your approach in plain words, including the electronics you would choose 2. Phase 1 price and timeline, plus estimated price for later phases 3. Parts cost per robot and monthly running cost for 2 to 3 robots 4. Which battery port and interface hardware you would use 5. Solo or team, and who does the hardware 6. Similar work you have delivered (links) 7. What you need from us, and the main risk you see BUDGET: Open to quotes DURATION: 1- 2 months and shall be extended based on deliverables phase wise. SKILLS: IoT, Embedded Systems, ESP32, Firmware, CAN Bus, RS485, Cloud, Dashboard, React, Python
Project ID: 40793678
74 proposals
Remote project
Active 9 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
74 freelancers are bidding on average ₹23,924 INR for this job

Custom IoT hardware, ESP32/STM32 firmware and MQTT-connected sensor networks are central to my work, making me well suited to connect your agricultural robots to a reliable field dashboard—not just produce a prototype. I work across embedded systems, firmware, Python, robotics and data visualisation, with the software and cloud capabilities needed to carry battery data from the robot through weak connectivity into usable operational views. For Phase 1, I can build around the two intelligent BMS units and evaluate CAN versus RS485 based on the protocol documentation, electrical robustness and available interface hardware. I can design the edge electronics and firmware to read rover and attachment battery data separately, buffer readings while offline, and synchronise them when connectivity returns. My IoT experience also supports the broader phases: sensor integration for spraying, load and motor monitoring for the carrier and weeder, MQTT data transport, and a simple dashboard that can later grow into a richer React-based system. I can provide the electronics recommendation, wiring and protection guidance, bill of materials, cloud/storage design and running-cost estimates as part of the phased delivery.
₹25,000 INR in 7 days
6.4
6.4

Hello Client, I propose a phased approach starting with Phase 1: focusing on power use monitoring for rover and attachments. I recommend using CAN bus to read battery data because it’s robust and standard for battery management communication, ensuring reliable integration with your BMS. For sensors and boards, ESP32 with CAN transceiver modules fits well for embedded control and IoT communication. We will design mounting and protection suitable for dust, water, and vibration. Data will be cached locally on the robot to handle connectivity gaps, syncing to the cloud when signal is available. The dashboard will use React with Python backend for scalable data visualization. I will provide a detailed parts list including ESP32, CAN modules, connectors, and sensor estimates, plus ongoing data plans suited for rural networks. Estimated parts cost is modest for each robot, and monthly running costs will cover connectivity and cloud hosting for 2-3 devices. I work solo with strong embedded and cloud expertise, covering hardware and software. My Phase 1 price is INR 20,000 with a 2-3 week timeline; later phases around INR 40,000+ depending on complexity. I will share similar IoT dashboards I’ve built after NDA. From you, I need BMS protocol docs and access to existing prototype. Main risk is ensuring reliable field connectivity and hardware ruggedness, which we will mitigate through design and local data buffer. Best regards, Mayank
₹18,000 INR in 12 days
5.7
5.7

Weak signal in Karnataka villages is your biggest risk. If the robot streams MQTT live with no local buffering, Phase 1 power data will have gaps, and your attachment comparisons won't hold up. Quick questions - Which SIM network and modem coverage do the pilot villages have, and do robots return nightly to a shed with WiFi? And does your prototype read battery data via a BMS over CAN/UART, or through shunt sensors? Here is the architectural approach: - FIRMWARE: An ESP32 buffers rover and attachment battery readings to flash, then syncs over MQTT with QoS 1
₹22,500 INR in 7 days
5.5
5.5

Could you share more details about the primary functions you want the dashboard to prioritize? For your project, I propose using ESP32 connected to CAN and RS485 for reading battery data; this method provides flexibility for connectivity challenges. In Phase 1, I can develop a basic dashboard focusing on power usage within 3 weeks. My estimated cost is $1000, and I’ll suggest parts costing around $150 per robot, with a running cost of approximately $50 monthly for 2-3 robots. I work solo on the embedded hardware and software integration. For similar projects, I have developed IoT solutions for agricultural systems that required real-time data monitoring and had limited connectivity. I will need access to the existing prototype and collaboration on the interface protocol from your side. Looking forward to discussing this further!
₹17,000 INR in 3 days
4.9
4.9

--- 1. Approach: I propose a phased development starting with Phase 1, focusing on power usage analytics for both rover and attachment batteries. For electronics, I recommend using ESP32 for its robust connectivity options and CAN Bus for reliable battery data communication due to its noise immunity and efficiency in embedded systems. For the dashboard, I suggest utilizing React for a responsive UI, with Python for backend data processing and storage. 2. Phase 1 Price & Timeline: - Price: $1,500 - Timeline: 2-3 weeks for initial dashboard to monitor battery power usage. 3. Parts Cost & Monthly Running Cost: - Estimated Parts Cost per Robot: $300 - Monthly Running Cost for 2-3 Robots: $100 (including data connectivity and maintenance). 4. Battery Port & Interface: I recommend using the CAN port for reading battery data, as it allows for robust communication in field conditions, essential for remote monitoring. 5. Team Composition: I will lead the project solo, with experience in hardware design and software integration, ensuring seamless execution. 6. Similar Work: I have successfully delivered IoT solutions in agriculture, including remote monitoring systems. [Provide links to relevant projects] 7. Requirements & Risks: I will need access to the existing prototype and the BMS protocol document post-NDA. The main risk is potential communication issues in areas with poor connectivity; I will implement a robust fallback mechanism. Best, Karthik
₹55,000 INR in 7 days
5.3
5.3

Hi, We’ll turn your agri-robot prototype into a reliable IoT monitoring system, tracking battery usage and comparing power consumption across attachments. With 7+ years of experience in embedded systems and software development, we’ll evaluate CAN vs. RS485, integrate ESP32 hardware, and build a cloud dashboard with offline data buffering. We’ll start with Phase 1, validate it on your robot, then expand through sensor integration and milestone-based delivery. Let’s open a chat or hop on a call to discuss your project in more detail and align the solution with what works best for you. Best Regards, Gensols
₹25,000 INR in 7 days
4.3
4.3

**Free right now and can start on your 5 robot pilot dashboard today** I am Anand. I build and fix web apps, servers and the automation that ties them together. My profile is 4.9/5 from 40 reviews with 98% of accepted jobs completed. My relevant skills here are Python and JSON. Recent work: Built a dashboard app that replaced an ops team spreadsheets. Migrated 40+ sites to a hardened VPS with zero downtime. Per robot view: I would show on or working, battery level, last known location and active problems. Data would update when signal allows and show last seen time when offline. Per task view: I would record litres sprayed, weight carried, area covered and power used per task. Each task would be saved with robot, start and end time, and totals. For the owner: One view for all 5 robots, full task history and money saved versus manual labour. That needs your manual labour cost rate to calculate honestly. For farmers: A simple Kannada view made for basic Android phones. Large text, few buttons, low data use and no heavy charts. 1. Your approach in plain words I would first reuse your battery prototype if its readings are reliable, otherwise replace that part. On the robot I would use a small controller to collect battery and task data and save it on the device when signal is weak. When signal returns it sends the saved data in order so nothing is lost. I would use Python on the server to receive and store it, then a simple web dashboard for the screens. I would choose store and forward over live only streaming because village signal is often weak. All code would go to your repository from day one with handover notes. 2. Phase 1 price and timeline, plus estimated price for later phases Phase 1 timeline is 2 to 3 weeks as you asked, for rover battery and attachment battery power use on a basic dashboard so you can compare attachments. I need to see your prototype code and one sample of its battery data before I give a fixed Phase 1 price, and I will give that fixed price before you award. Later phase prices for spray, carrier and weeder, owner view and handover should be fixed after Phase 1 is accepted, as you planned, because they depend on the sensors proven in Phase 1. 3. Monthly running cost for 5 robots For 5 robots the main costs are one small cloud server, database storage and a SIM data plan per robot. I would keep it on one small server at pilot stage to keep cost low. Exact monthly cost depends on how often robots send data and how long you keep history, and I will confirm it in the fixed quote with the server size named. 4. Solo or team, and who does the hardware Solo. I do the Python, server, data flow and dashboard work myself. For hardware I need your robot side access and help with physical fitting and wiring on the robot, as I am not claiming embedded hardware delivery I cannot support. I will define exactly what data I need from the robot and in what format. 5. Similar work you have delivered The closest true examples are the dashboard app that replaced an ops team spreadsheets and server work keeping systems online during migration. I have no public links I can honestly share for those, so I will not invent any. 6. What you need from us and the main risk you see I need access to your repository, your current battery prototype and its code, sample battery data, and one robot or recorded data to test against. I also need your manual labour cost if you want the savings figure in later phases. The main risk is weak field signal causing gaps, which the on robot saving and delayed sending is designed to handle. The second risk is battery readings that drift between attachments, so Phase 1 should compare readings against a known load early. Can you share your prototype code and a sample of the battery data it produces so I can give you the fixed Phase 1 price?
₹17,700 INR in 7 days
3.6
3.6

Hi, Ankit here, from Bahrain. Building your agri-robot IoT dashboard with three attachments and four communication wires comes down to one thing: a device that behaves the same in the field as on the bench. I'm a senior embedded and electronics engineer with 10+ years of experience working with Internet of Things (IoT), Python, Embedded Systems and ESP32. With ESP32, the real challenge is timing, power and real conditions. My plan: first, review the schematic, pin map and timing requirements. Then, write the firmware in small modules, each tested on the board. Finally, test on the real hardware under load, power loss and bad signal. The price, timeline and milestones are in the bid details. I work on it myself. I've done firmware work in ESP32, so I check early for timing issues and power drops. A few questions to better understand the scope: 1. Will it run near motors or long cables? Noise there corrupts readings, so I test early. 2. Use the vendor HAL except where timing is tight? I'd recommend it, it's easier to change later. 3. Is this heading to production after the prototype? Then parts and code stay ready for production. Happy to go over the details here in chat and suggest the best approach. Looking forward to hearing from you, Ankit
₹25,000 INR in 4 days
3.7
3.7

1. Technical approach Robot hardware and data collection Review your current battery-reading prototype, sensors, controller, and firmware. Capture rover battery voltage, current, power consumption, and energy used where the hardware supports reliable measurement. Measure the attachment battery separately so power consumption can be compared across attachments. Add timestamps, robot identifiers, and sensor-health information to each reading. Connectivity for village conditions Use Wi-Fi or cellular connectivity where available, depending on coverage and hardware. Buffer readings locally when the connection drops and upload them automatically when connectivity returns. Send compact data packets using MQTT or HTTPS, with retries and timestamps to minimise data loss. Evaluate the appropriate connectivity hardware after checking the pilot locations and existing electronics.
₹25,000 INR in 7 days
3.1
3.1

Embedded systems and IoT development are central to my work, making me well suited to connect your robot battery data to a practical field dashboard. I develop embedded solutions with Arduino, ESP and C/C++, and can support the electronics, firmware and system integration needed to read both intelligent BMS units and transmit reliable operating data. For Phase 1, I would evaluate the BMS CAN and RS485 interfaces from the protocol documentation and select the port that provides the most reliable, well-supported data access. My recommendation would include the required interface hardware, protected power design, wiring, PCB considerations and mounting suitable for dust, water and vibration. The initial dashboard can focus on separate rover and attachment battery level, voltage/current or power data, energy use and online/offline status, with data buffering considered for weak field connectivity. My PCB design experience with KiCad, Proteus and Altium, together with embedded IoT skills, supports a complete hardware-to-software implementation and clear handover documentation. I can provide the Phase 1 electronics recommendation, parts list and running-cost estimate, then extend the same platform for sprayer, carrier and weeder telemetry. I am ready to contribute as the embedded hardware and firmware engineer for this project and discuss the phased scope with you.
₹20,500 INR in 7 days
3.3
3.3

Hi, I have 16 years of experience in electronics R&D, embedded systems, IoT hardware, firmware, and cloud integration. I can independently handle hardware, firmware, and dashboard integration. **Proposed approach:** - Use an ESP32 controller to read both BMS units independently. - Prefer RS485 initially, subject to protocol compatibility; CAN is an alternative. - Monitor voltage, current, SOC, power, and energy consumption. - Use 4G/Wi-Fi with local data storage and automatic cloud synchronization when connectivity returns. - Develop a basic dashboard for battery status and energy comparison. - Later integrate GPS, flow sensors, tank-level sensors, load cells, and motor monitoring. **Estimated cost:** - Phase 1: ₹20,000–25,000 (2–3 weeks). - Later attachment integration: ₹10,000–15,000 each. - Hardware: ₹5,000–8,000 per robot (estimate). - Cloud: ₹500–1,500/month for 2–3 robots. I will handle hardware and firmware directly, with code maintained in your repository from day one. Relevant experience includes ESP32 IoT systems, CAN/RS485/Modbus, industrial data logging, battery monitoring, and cloud-connected products. **Required:** BMS model and protocol documents (after NDA), existing prototype details, and access to one robot. **Main risk:** BMS protocol compatibility and weak field connectivity. Both will be validated during Phase 1. Best regards, Subhash Suman Embedded Systems | ESP32 | CAN/RS485 | IoT | Cloud Integration
₹20,000 INR in 7 days
3.0
3.0

Hello, I can support your project with the embedded hardware and firmware development, starting with Phase 1. My approach would be to use an STM32 or ESP32 controller to communicate with both BMS units independently and collect battery voltage, current, power, and energy consumption data. I recommend using CAN as the primary interface if your BMS protocol supports it, due to its robustness in electrically noisy environments. RS485 would also be a suitable alternative depending on the available protocol. My responsibilities would include: - Reviewing the existing hardware and BMS communication protocol. - Designing the required interface and protection circuitry. - Developing firmware for battery data acquisition and processing. - Implementing reliable communication and offline data buffering. - Integrating the embedded system with the selected IoT platform. My main expertise is embedded hardware, PCB design, and firmware development using STM32 and ESP32. For the cloud backend and dashboard, I can coordinate the integration with a dedicated software developer if required. I'm also comfortable signing an NDA and working with your team through paid milestones, with all source files and designs delivered to your repository. Best regards Eng Mahmoud Ibrahim Electronics Enginner Replies in 10min
₹25,000 INR in 7 days
3.6
3.6

I reviewed your specifications for 'Agri-Robot IoT Dashboard Build'. The key technical priority is a scalable backend architecture with clean separation of concerns and secure data flow. Here is how I plan to handle the initial delivery milestone: - Database & Model Design: Design normalized MySQL schemas with appropriate indexing, foreign keys, and query optimization. - API & Business Logic: Build RESTful endpoints using PHP and MySQL with strict input sanitization, token auth, and error handling. - Integration & Testing: Connect frontend interfaces, verify third-party webhooks/payment APIs, and conduct comprehensive integration testing. Key Clarification Question: Are the database schema and API endpoints already documented, or will we design the data contracts during the initial phase? I am available to implement the core API endpoint or database schema as a low-risk initial milestone so you can verify the code quality.
₹12,500 INR in 4 days
0.4
0.4

Hello, I’m Ankur, a freelance AI and Full Stack Developer with a skilled team of professionals. I’ve gone through your project requirements for {Agri-Robot IoT Dashboard Build}, and I’m confident that I can deliver an intelligent, efficient, and scalable solution tailored to your needs. With years of experience in Artificial Intelligence, Machine Learning, Deep Learning, and NLP, I’ve successfully built AI-powered applications, chatbots, automation tools, and predictive models for clients across various industries. You’ll receive a complete, production-ready solution with clean code, accurate results, and 3 months of post-launch support. My goal is to combine technical expertise with real-world problem-solving to ensure your project’s success. Let’s connect and discuss your ideas — I’m ready to bring them to life. Best regards, Ankur Hardiya AI & Full Stack Developer
₹25,000 INR in 7 days
0.2
0.2

I can deliver 'Agri-Robot IoT Dashboard Build' end to end — clean architecture, tests, and deployment. I'll start with a short plan, share progress daily, and hand over production-ready code. Could you confirm your timeline and must-have features so I can lock the scope?
₹16,119.60 INR in 7 days
0.0
0.0

✔ I deliver 100% work — 99.9% is not for me. Workflow Diagram Hardware Review ⟶⟶ ESP32 Integration ⟶⟶ Offline Data Logging ⟶⟶ MQTT/Cloud Sync ⟶⟶ Dashboard ⟶⟶ Field Testing ⟶⟶ Handover Key Highlights ✔ IoT architecture — ESP32, Python, MQTT, React, and cloud integration. ✔ Battery monitoring — measure rover and attachment voltage, current, power, and energy consumption. ✔ Weak connectivity — store readings locally and synchronize automatically when coverage returns. ✔ Real-time tracking — robot location, battery status, working state, and fault alerts. ✔ Task analytics — spraying litres, carried weight, covered area, and power consumption. ✔ Owner dashboard — monitor 5 robots, task history, and estimated labour savings. ✔ Farmer interface — lightweight Android-friendly Kannada web dashboard. ✔ Low-cost hosting — approximately $10–$25/month plus SIM data. ✔ Full ownership — source code, hardware designs, documentation, and client-controlled repository. ✔ Milestone delivery — validated on actual robots before acceptance.. Complete Pilot: $3,000 | 8–12 weeks. Best Regards, Asad IoT Engineer | ESP32 | Python | Robotics | Cloud
₹18,000 INR in 14 days
0.0
0.0

Hi, I can deliver "Agri-Robot IoT Dashboard Build" as working code with tests and a short README within 2 days of award. How I work: I confirm any open point in my first message, deliver in a single milestone, and include one round of revisions. I can start as soon as the milestone is funded. Could you share one sample input with the expected output, or the tool versions you target?
₹14,375 INR in 2 days
0.0
0.0

My strength is building real-time analytics dashboards that turn operational data into clear, usable decisions. Your agri-robot pilot needs a simple view of battery usage, robot status, task history and field activity, and my experience with data visualization and modern dashboard technologies is directly relevant to presenting this information clearly. I can build the dashboard layer using React and connect it to REST APIs and a suitable data store such as MongoDB or SQLite. My automation work includes complete, documented systems with reporting, tracking and scalable workflows, which fits your requirement for repository-based code and handover documentation. I can also make the interface practical for basic Android phones and structure it for Kannada content. However, my profile does not demonstrate embedded hardware, ESP32, firmware, poor-connectivity field systems, or agriculture-specific delivery, so I would not claim those capabilities or invent Phase 1 pricing, running costs, or similar-project links. I would be a strong choice for the data, API, dashboard and visualization side of this project, while embedded and field-connectivity work should be handled by a specialist partner or team member. I am ready to discuss how my dashboard expertise can contribute to a reliable pilot handover.
₹12,800 INR in 5 days
0.0
0.0

Hi there, I can help build an IoT monitoring system for your agricultural robots, connecting battery sensors, embedded firmware, cloud storage, and a simple mobile-friendly dashboard. For Phase 1, I’d first assess your existing battery prototype, then capture rover and attachment battery data using ESP32 or compatible hardware. I’d use MQTT with local buffering and automatic retries to handle weak village connectivity, alongside a Python backend and dashboard showing live readings, history, and attachment-level power comparisons. The interface can be designed for basic Android phones, with Kannada support in later phases. I’d structure the system for future spray, carrier, and weeder metrics, keeping all code in your repository with clear documentation. I’d confirm hardware compatibility and connectivity before finalising the architecture and operating costs. Do your current robots already use ESP32, and what battery voltage/current sensors does the prototype provide? Best regards,
₹20,000 INR in 2 days
0.0
0.0

You need a reliable telemetry system that eliminates the guesswork from your field pilot, giving you precise data on how each attachment impacts battery life and operational efficiency. I will implement a robust "store-and-forward" architecture to ensure no data is lost during the frequent signal drops common in Indian agricultural fields. For the battery interface, I recommend using the CAN port; its differential signaling is far more resistant to the electromagnetic interference generated by your robot's motors compared to RS485. My delivery plan is entirely done-for-you: 1. Hardware Architecture: Selecting industrial-grade ESP32-based controllers and CAN transceivers, providing full wiring diagrams and mounting specs for dust/water protection. 2. Firmware Development: Implementing local buffering (SPIFFS/LittleFS) to queue data while offline and sync via MQTT once connectivity returns. 3. Cloud Pipeline: A Python-based backend and a clean dashboard to visualize power draw per task and attachment performance. You will see your first real-time battery telemetry stream on a basic dashboard within the first 10 days. I have previously deployed similar IoT pipelines handling indust
₹150,000 INR in 60 days
5.1
5.1

Bengaluru, India
Member since Aug 16, 2026
$2-8 USD / hour
₹12500-37500 INR
$1500-3000 USD
₹12500-37500 INR
₹150000-250000 INR
min $10 USD
$80-95 USD / hour
€30-250 EUR
$10-30 USD
€30-250 EUR
$15-25 CAD / hour
₹750-1250 INR / hour
$250-750 USD
€18-36 EUR / hour
$10-30 USD
₹12500-37500 INR