Devam Ediyor

CAD drawing with dimensions for fishing lure

I need some CAD drawings done on a fishing lure I have developed. It is important to have all dimensions clearly represented on the drawings. Additionally, I would like to be able to input the specs from the CAD drawings into a 3D printer and make the lure with tight tolerances. The lure measures a length of 4 1/2" in a straight line, not following the arch. Looking down on the lure, it's width at it's widest point is 11/16" and 5/16" at the narrowest point at each end prior to the radiused rounded ends. Looking at the side view, the lure measures 7/16".The sponge shown is 2 1/2" long, 1/4" wide and 3/16" deep and is used to soak up liquid scent which is injected into the 1/8" diameter hole on the bottom of the lure (not the side as shown in a couple of the drawings) and closed up with a rubber grommet. With the lure placed on a flat surface and each end touching the flat surface, the arch of the lure measures 5/8" from the flat surface up to the bottom of the lure at the tallest part of the arch. The hooks are a #2 treble hook (diameter of 1 1/8" across). In the "ExpandedviewSuperBait" attached file, the yellow "waterproof net" is not needed for these drawings and will not be used in the end product. In the "super bait_1" file, the metal loops at both ends should be metal color and the red dot at one end is the head of the lure and should be a 3d fish eye. The fish eye should also be on the bottom side of the head of the lure.

I do not own CAD software so the drawings need to be in a format that I can see and print. I have attached a photo of some very similar lures to my design. The difference is that my lure does not open and there are no hinges which can break.

For those interested in more work, I have also attached a couple files for another lure I am developing. The files are call LivingFlatFish. This lure measures 5" long and has an arch of 13/16" measured with the lure on a flat surface with both ends touching the flat surface, from the flat surface up to the bottom of the lure at the tallest part of the arch. The width of the lure (in top view) is 1 1/4" at the front end just prior to beginning the radiused rounded head. The width of the tail of the lure is 11/16". The depth of the lure is thickest at 3/4" and approximately 2" from the tail of the lure. The thickness tapers to about 1/2" at the point going toward the head where the fishing line attaches to the lure where the lure has a slight concave or cupped shaped used to make the lure dive in the water while trolling.

Thank You,

Dean Bellamy

Beceriler: 3D Rendering, AutoCAD

Daha fazlasını görün: cad lure, cad drawings dimensions, lure drawing, drawing lures, cad fishing lures, cad drawing dimensions, fishing lure cad, fishing lure drawings cad file, lures drawing, fishing lure drawing dimensions, width fishing lure, fishing lure cad files, drawings fishing lures, fishing lure cad file, lure design drawings, lure cad, cad fishing lure, design fishing lures cad, fishing lures cad, fishing lure printer, top down cad design, top 5 product design software, top 5 3d rendering software, top 3d rendering software, some one drawing

İşveren Hakkında:
( 0 değerlendirme ) Colbert, United States

Proje NO: #4451089

9 freelancers are bidding on average $113 for this job

almiradjo

Hello! I am interested to work on your project. Ready to start working immediately. Best regards!

in 3 gün içinde55$ USD
(75 Değerlendirme)
6.0
saledj2010

I already have 100% satisfied employer for the similar job like Yours.

in 3 gün içinde60$ USD
(12 Değerlendirme)
4.2
JakubPOL

Hi! Gladly will draw the lure for you. Check PM for details. Thanks.

in 5 gün içinde88$ USD
(9 Değerlendirme)
3.8
LogCad

Hello, would you please upload the picture/image?

in 3 gün içinde82$ USD
(2 Değerlendirme)
2.2
SolidDrafter3D

Hello. I am interested in your project, please check PM. Thanks a lot.

in 3 gün içinde50$ USD
(2 Değerlendirme)
2.2
xodesignlabs

I can provide the level of detail needed

in 3 gün içinde100$ USD
(1 Değerlendirme)
2.2
Runner20k

I am a UK based degree qualified mechanical engineer with over 20 years experience in the use of Auto CAD 2d and 3d and also in the use of Autodesk Inventor and Solidworks I have been working as a freelance design e Daha fazlası

in 5 gün içinde88$ USD
(1 Değerlendirme)
1.4
tkdsaji

hello I ready to start your work.

in 5 gün içinde110$ USD
(0 Değerlendirme)
0.0
cad0nduty

Kindly see my PM. Thanks

in 3 gün içinde385$ USD
(0 Değerlendirme)
0.0