
Closed
Posted
I am looking to deploy a Universal Robots cell that can safely lift stainless-steel frames arriving in a single stack and place each one into a downstream machine or work-station. Because the frames are both delicate and irregular, the end-of-arm tooling must constantly adjust its grip through real-time force feedback so there is zero risk of distortion or scratching. Here is what I need from you: • Complete UR program (PolyScope / URScript) that detects the top frame in the stack, applies just enough force to grasp it, and releases it precisely at the target location. • Integration of a compatible force-torque sensor and the logic that modulates grip pressure throughout the motion. • Gripper selection or custom design guidance suited to thin stainless-steel profiles, including finger geometry and compliant pads. • Documentation and a quick-start guide covering sensor calibration, stack height adjustment, and teach-point updates so my technicians can make routine tweaks without rewriting code. Acceptance criteria • Robot consistently removes one frame at a time from the stack without jamming or double-picking. • Maximum surface deflection on any frame stays below the tolerance we verify with a simple feeler-gauge test. • Cycle time meets or beats the manual process it will replace. Experience with UR models, force-torque integration, and past projects handling fragile metals will be key. If this sounds like your specialty, I’m ready to review your proposed approach and timeline.
Project ID: 40802714
42 proposals
Remote project
Active 5 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
42 freelancers are bidding on average €25 EUR/hour for this job

Hey, with thin stainless frames stacked directly on each other, the hardest acceptance point is usually “no double-picking.” Flat stainless sheets cling together, especially with any oil film, so the frame underneath often lifts with the top one. The common fix in sheet handling, magnetic fanners, won’t work here because 304 and 316 stainless aren’t magnetic. Instead, I’d use a peel lift: raise one edge slightly first to break the seal, then lift fully, with an air knife at the stack edge if needed. The force-torque sensor then checks the weight right after lifting. If it reads close to two frames, the robot sets them back down and retries before anything moves on. For finding the top frame, the robot can use force mode to search down until it gently touches the stack, so the stack height never has to be set by hand, and it adapts automatically as the stack shrinks. If you’re on an e-Series UR, the built-in force-torque sensor may handle most of this, with an external sensor only needed for very light frames. For gripping, I’d suggest a force-controlled electric gripper with non-marking polyurethane pads, closing straight onto the profile without sliding, which is what causes most scratches. You’d get the URScript program, calibration and teach-point documentation, and a quick-start guide for your technicians. Which UR model do you have, and how much does each frame weigh? Juan Pablo
€25 EUR in 40 days
6.2
6.2

Hi, I understand you need a Universal Robots cell to remove one delicate stainless-steel frame at a time, using force feedback to avoid double-picks, marks, and distortion. I can build the URScript/PolyScope sequence, add top-frame detection, control the force-torque sensor during gripping and placement, and help define suitable fingers and compliant pads. I will also include simple settings for calibration, stack height, teach-point updates, and routine troubleshooting so your technicians can adjust the cell without rewriting the program. The testing plan will focus on your feeler-gauge limit, reliable single picking, and cycle time compared with the manual process. What UR model, frame dimensions and weight range, force-torque sensor options, and target cycle time should the solution support? Please start a chat and let’s discuss your UR model, sensor choice, frame dimensions, and target cycle time.
€26 EUR in 20 days
5.5
5.5

⭐⭐⭐⭐⭐ Deploy UR Cell for Safe Handling of Stainless‑Steel Frames with Real‑Time Force Feedback ❇️ Hi My Friend, I hope you are doing well. I checked all of your project requirements and I can see you are looking for a UR cell that lifts delicate frames. You have no need to look any further as Zohaib is here to help you! My team is already doing 50+ similar projects for robotic handling of fragile metal parts. I will build a complete URScript program that detects the top frame, applies just enough grip using force‑torque feedback, and places it precisely. I will also give a quick‑start guide and sensor calibration steps at no extra cost. ➡️ Why Me? I can easily do your UR cell as I have 5 years of experience in UR programming, force‑torque integration, robot kinematics, and compliant gripper design. Not only this, I have a strong grip on sensor calibration, custom end‑effector design, and cycle‑time optimization. ➡️ Let's have a quick chat to discuss your project in detail and let me show you samples of my previous work. Looking forward to discussing with you in chat. ➡️ Skills & Experience: ✅ URScript ✅ PolyScope ✅ Force‑Torque Sensors ✅ Gripper Design ✅ Compliance Pads ✅ Real‑Time Control ✅ Sensor Calibration ✅ Cycle Time Optimization ✅ Metal Handling ✅ Automation Integration ✅ Documentation ✅ Quick‑Start Guides Waiting for your response! Best Regards, Zohaib
€22 EUR in 40 days
5.8
5.8

Hello, I am Dr. Rajesh Rolen, PhD in Computer Science & Engineering, with experience of over 20+ years in Robotic Process Automation, Automation As a preferred freelancer in the top 1%, I have done 400+ projects here on freelancer.com, I have 4.9 ratings out of 5 on average, which showcases my quality of work and timely delivery. Key Highlights: - Free Hosting Support on the Cloud or any desired platform. - Free 3 months of post-delivery support to ensure that our client doesn’t face any challenges after the launch of the project. - Free Dedicated tester on projects to ensure quality delivery, so clients don’t need to act as a tester. - 10+ Years experience UI/UX team to ensure intuitive UI. Portfolio: https://www.freelancer.com/u/Microlent Please open the chat and send me a message, so we can have a more detailed discussion about the project to give you the project timeline and cost. Thank you for considering my services. I look forward to engaging in a productive conversation and understanding how I can be of assistance in bringing your project to life. Regards Rajesh Rolen
€18 EUR in 40 days
4.0
4.0

Force feedback and sensor integration are central to your UR pick-and-place cell, and Robotics plus Sensor Integration are core capabilities I offer through a systems-focused engineering team covering industrial automation, instrumentation, motion control, machine vision, electronics and embedded systems. I can develop the PolyScope/URScript logic for controlled frame detection, force-based gripping, safe single-part removal and accurate placement, while integrating the selected force-torque sensor with the robot control sequence. My electronics and embedded experience—including STM32, ESP32, Arduino, Raspberry Pi, ARM, RTOS and industrial communications—supports reliable sensor interfacing and calibration. Mechanical CAD/CAM capabilities in SolidWorks, Fusion 360, AutoCAD, CATIA and sheet-metal design also support practical guidance for compliant gripper fingers and protective pads suited to delicate stainless-steel profiles. I will provide clear documentation covering calibration, stack-height adjustment and teach-point updates so technicians can maintain routine settings confidently. I would welcome the opportunity to deliver a robust, serviceable force-sensing robot solution for your cell.
€27 EUR in 40 days
4.0
4.0

Hi, Handling delicate stainless-steel frames requires precise force control, reliable single-part detection, and carefully designed gripper contact surfaces. The key is preventing excessive clamping force while maintaining stable handling throughout the pick-and-place cycle. I'd approach this using a Universal Robots force-torque sensing setup, compliant gripper fingers, and adjustable contact pads suited to thin stainless-steel profiles. The control architecture would account for stack-height variation, grasp verification, controlled lifting, and release-position accuracy. I'd also focus on detecting double-picks, handling failed grasps, and introducing safety checks before transferring each frame to the downstream station. My background includes technical troubleshooting, API-driven automation, and structured system workflows. I'd first review your UR model, frame geometry, weight, and allowable deflection to establish the appropriate control and tooling design. The objective would be a maintainable setup with documented calibration, teach-point adjustment, and recovery procedures. Best Muhammad Saad
€20 EUR in 40 days
3.4
3.4

Hi there, I can provide a comprehensive URScript program that addresses your requirement for lifting and placing the delicate stainless-steel frames. My approach will involve precise real-time feedback from the force-torque sensor to modulate grip pressure effectively, ensuring zero distortion during handling. Additionally, I can assist in selecting or designing a custom gripper tailored to accommodate the thin profiles of the frames, ensuring effective and safe manipulation. To ensure your team can efficiently manage daily operations without needing to rewrite code, I will include detailed documentation covering sensor calibration and stack height adjustments. This project aligns well with my experience in automation and delicate metal handling, positioning me to deliver results that meet your acceptance criteria. Looking forward to your response. Regards, Ali
€18 EUR in 1 day
3.2
3.2

Handling delicate stainless-steel frames requires careful coordination between force feedback, gripper geometry, stack-height detection, and robot motion. The priority would be reliable single-frame picking without introducing surface scratches or permanent deformation. I'd approach this by first evaluating the UR robot model, frame geometry, material thickness, stack arrangement, and downstream placement requirements. The solution would cover force-torque sensor integration, adaptive gripping logic, compliant gripper fingers, stack-height compensation, and controlled release. I'd also consider double-pick detection and recovery conditions to improve operational reliability. The URScript/PolyScope program would be modular and documented, with configurable sensor calibration, teach points, stack height, and operating parameters so technicians can make routine adjustments. I'd validate the system against your actual deflection tolerance, single-pick reliability, and cycle-time requirements before production deployment. Could you share the UR model, approximate frame dimensions and weight, and whether the frames have accessible gripping edges?
€25 EUR in 40 days
3.4
3.4

Hi there, The hard part is not just programming the UR cell but ensuring that the gripper consistently adapts to the delicate frames without causing damage. First, we’ll focus on integrating the force-torque sensor to provide real-time feedback, allowing the gripper to adjust its pressure dynamically throughout the operation. Choosing the right gripper design is crucial; I can guide you on finger geometry and compliant pad selection tailored for thin stainless-steel profiles. Could you clarify if there are any specific environmental conditions or additional features required for the setup? Looking forward to discussing the details in chat.
€27 EUR in 40 days
2.7
2.7

Hi, I’m a Mechanical and Automation Engineer with 10 years of experience in mechanical design, industrial automation, embedded systems, and prototype development. I can support the development of your UR robotic handling solution. My proposed approach includes: - Developing the UR robot program using PolyScope/URScript. - Integrating force-torque sensing for controlled gripping and motion. - Designing or selecting a suitable gripper with compliant, non-marking contact pads. - Implementing top-frame detection, single-part separation, and double-pick prevention. - Optimizing robot movements and cycle time. - Preparing sensor calibration instructions, teach-point adjustment procedures, and technician documentation. Estimated timeline: 3–5 weeks, subject to robot model, sensor, gripper, and frame specifications. Before confirming the quotation, I would like to clarify: 1. Which UR model are you using (UR5e, UR10e, UR20, etc.)? 2. Do you already have a force-torque sensor and gripper? 3. Could you provide frame dimensions, weight, material thickness, and allowable deflection? 4. Is the stack height fixed or variable? I can also support custom gripper mechanical design and prototyping. My priority would be to develop a reliable handling solution and validate gripping force, surface protection, and single-frame separation through practical testing before final acceptance. I would be happy to review your technical details and propose the next steps. Best regards,
€30 EUR in 40 days
2.8
2.8

I can develop the URScript/PolyScope workflow for reliable single-frame pick-and-place, combining stack-top detection, force-controlled engagement, compliant gripping, and controlled release. The implementation would include: - Force/torque sensor integration with calibration and safety limits - Contact detection and grip-force modulation to prevent distortion or scratching - Logic to distinguish one frame from double-picks or jams - Configurable stack-height compensation and teach-point parameters - Motion sequencing optimized around your manual cycle-time target - Guidance for gripper fingers, compliant pads, and contact geometry suited to thin stainless-steel profiles - Technician-focused documentation and a quick-start procedure for calibration, stack adjustments, and routine point updates I would structure the program with clearly exposed parameters, recovery handling, and conservative force limits so validation against your feeler-gauge tolerance can be performed systematically. The final workflow can be tested against your UR model, sensor interface, frame geometry, and downstream machine handoff requirements.
€18 EUR in 18 days
2.6
2.6

Hi, I can build the UR pick-place logic that lifts one stainless-steel frame at a time, adapts grip force from live force-torque feedback, and places each part without bending or scratching it. For thin, irregular frames, I’d use a guarded approach with force-based contact detection, then tune the grip so the robot only applies the minimum holding force needed during lift and transfer. I can deliver the PolyScope/URScript program, sensor integration logic, gripper guidance for compliant fingers and pads, and clear documentation for calibration, stack-height updates, and teach-point changes. I’ll also test for single-part pickup, no-jam behavior, and stable force limits against your feeler-gauge check. I’m available in Spain time and can work with your technicians on any routine adjustments. If you want, I can also advise on the best sensor mounting point for clean force readings. Please message me in inbox and we can discuss the setup further. Best regards, Ali Haider
€27 EUR in 40 days
0.9
0.9

My multidisciplinary automation and machinery-engineering background aligns closely with a UR pick-and-place cell for delicate stainless-steel frames. I work across industrial automation, sensors, instrumentation, control panels, safety systems, mechanical design, and material-handling equipment, allowing the robot program, force-sensing hardware, and tooling to be treated as one reliable system. I can contribute to the UR/PolyScope and URScript logic, sensor integration, calibration documentation, and practical gripper development for thin, irregular profiles. My SolidWorks and AutoCAD experience supports accurate finger geometry, compliant pad concepts, assemblies, and manufacturing drawings, while my experience with machine design, conveyors, pneumatics, encoders, PLC/HMI systems, and industrial safety helps ensure the cell is suitable for commissioning and technician maintenance. I will keep the documentation focused on stack-height adjustment, teach-point updates, calibration, and routine operation. I am ready to apply this combined mechanical and automation expertise to develop a careful, manufacturable solution for consistent single-frame handling.
€18 EUR in 40 days
1.0
1.0

Hi - read through your post, this looks doable. You'll get a complete UR program using PolyScope that implements real-time force feedback for safe handling of your delicate stainless-steel frames, along with a quick-start guide for sensor calibration and adjustments. I'll also provide recommendations for the gripper design that ensure a secure and gentle grasp on the irregular profiles. Happy to answer anything before you decide. Appreciate it!
€29 EUR in 40 days
0.0
0.0

Hello, My automation skills can support the software and control side of your UR pick-and-place cell, particularly where dependable sequencing and repeatable machine interaction are essential. I can develop a tailored automation solution around the required pick, place, release, and technician-adjustable settings rather than relying on a generic workflow. Your project also requires clear operator-facing documentation, and my full-stack technical background allows me to present configuration guidance in a practical, accessible format. I can structure the UR program documentation around sensor calibration, stack-height adjustments, teach-point updates, and routine parameter changes so technicians can maintain the system without rewriting the complete logic. I would be glad to contribute to this automation project and provide a focused implementation aligned with your handling and usability requirements. Thanks!
€18 EUR in 19 days
0.0
0.0

I’ve programmed UR pick-and-place cells for delicate metal parts, including force-guided gripping and repeatable stack separation. For this project, the key is combining a wrist force-torque sensor with compliant, profiled gripper fingers, because thin stainless frames need controlled contact rather than fixed clamp pressure. I’ll build the PolyScope/URScript sequence for top-of-stack detection, adaptive grasping, transfer, and precise release at the downstream station. I’ll provide gripper geometry guidance with non-marring pads and parameters technicians can adjust for stack height, calibration, and teach points. I’ll validate single-frame picks, verify deflection with your feeler-gauge method, and tune motion for cycle time. Thanks, Kittipong
€18 EUR in 37 days
0.0
0.0

Hi, "Force-Sensing UR Pick-Place Robot" is right in my wheelhouse. I'm a senior engineer (11+ yrs) specialized in API integration (REST/webhooks/OAuth, connecting third-party services end to end), which is exactly what this needs. I've shipped my own products end to end and focus on reliable, maintainable delivery. How I'd approach it: 1) Confirm the exact scope and edge cases with you 2) Build in small, testable steps so you see progress early 3) Clean handover with docs I'm available to start now. Let me know your questions. Best Chris
€18 EUR in 1 day
2.4
2.4

Hi, I read your project details for the UR robot cell to handle delicate stainless steel frames with controlled grip force. I can develop the URScript and PolyScope program with real time force feedback from a compatible force torque sensor. I can also configure single frame detection, precise placement and grip control to prevent scratches and frame distortion. ✔ Robotics Tasks I Will Handle: • URScript control for top frame detection and single frame pick. • Force torque sensor integration with adaptive grip pressure and compliant gripper pads. • Sensor calibration, stack height adjustment and teach point guide. ✔ Two Quick Questions: 1. Which UR model and controller version do you use? 2. Which force torque sensor is available? FYI: I can start immediately with the robot program, sensor calibration and grip force tests against your deflection tolerance. Please message me on chat to discuss the gripper design and target cycle time. Kind regards, Yogesh Arora
€18 EUR in 40 days
0.0
0.0

I will develop a complete PolyScope and URScript robotic cell that safely destacks your irregular stainless-steel frames using real-time force-torque feedback to eliminate scratching and distortion. To prevent surface deflection, I will write a dynamic control loop utilizing UR's Force control to modulate grip pressure, paired with custom polyurethane-coated end-of-arm tooling to distribute contact force evenly. This logic will automatically index the stack height and guarantee single-part picking without jamming. I have extensive experience integrating Universal Robots with advanced force-feedback sensors for fragile manufacturing applications. Are you using an e-Series UR robot with the built-in force-torque sensor, or do we need to specify an external sensor package?
€23 EUR in 40 days
0.0
0.0

Hi, I can help develop your Universal Robots pick-and-place system, focusing on precise frame handling, adaptive gripping, and reliable force feedback. I'd recommend separating the workflow into three controlled stages: stack detection, force-regulated gripping, and accurate placement. I'll first review your UR model, existing tooling, sensor setup, and frame geometry to determine the safest implementation. Using PolyScope and URScript, I'll develop configurable routines for detecting the top frame, adjusting stack height, controlling approach movements, and monitoring force-torque feedback. For the gripper, I'll recommend compliant contact pads and adjustable gripping force to minimize scratches and deformation. I'll also implement single-frame pickup verification, abnormal-force detection, controlled fault recovery, and configurable teach points. My suggested first milestone is a working single-frame pick-and-place demonstration. We'll validate gripping force, frame deflection, and cycle time before extending the program to continuous operation. I'll provide the robot program, calibration procedures, operating parameters, and technician documentation. I estimate 3–5 weeks, including hardware integration and physical validation. Which UR model, force-torque sensor, and gripper are currently installed?
€20 EUR in 40 days
0.0
0.0

Johannesburg, Spain
Payment method verified
Member since Apr 3, 2023
$250-750 AUD
₹12500-37500 INR
€18-36 EUR / hour
₹12500-37500 INR
$250-750 USD
$750-1500 USD
$30-250 NZD
₹1500-12500 INR
min $50 USD / hour
€18-36 EUR / hour
$30-250 USD
₹100-400 INR / hour
$15-25 CAD / hour
$250-750 USD
$30-250 USD
₹1500-12500 INR
$2-8 USD / hour
$8-15 USD / hour
$30-250 USD
₹12500-37500 INR