Kapalı

connecting multiple i2c devices with single controller

Bu iş için 18 freelancer ortalamada ₹658/saat teklif veriyor

arrijal1992

Hi, Theoretically, I2C bus can handle up to 128 devices with only 1 master. I think, You should check two things: 1. did you already use pull up resistor over SDA and SCL pin? 2. did that two IC have same I2C address? Daha Fazla

₹600 INR / saat
(19 Değerlendirme)
4.5
jitendrabaraiya

I can do your job

₹1111 INR / saat
(6 Değerlendirme)
4.3
₹1000 INR / saat
(14 Değerlendirme)
4.0
mcprogrammer

Hi! Do you have schematics for the project? Or maybe just a sketch regarding the two chips you've mentioned?

₹638 INR / saat
(1 Yorum)
3.0
vpr58e3445e03cda

We have gone through the requirements that you have mentioned and we will help you in this. Message us for further discussion. Feel Free to contact us. Thank you!

₹638 INR / saat
(1 Yorum)
1.0
AbdRao

Hi, I can do your work. I have experience of getting data from multiple module on I2C wire. Based on my experience I am sure I will be able to overcome the difficulties you are facing in I2C communication.

₹777 INR / saat
(1 Yorum)
0.8
venkat7401

I would like to answer your problem i was working with i2c, spi protocols in pic controllers i can clear your problem if you have ping me

₹638 INR / saat
(0 Değerlendirme)
0.0
munshisohel1144

Hello, My name is muhammed sohel and i am expert in circuit and PCB design.  I am writing in response to your job posted on freelancer. please accept this letter as my application for electronics engineer. I Would lov Daha Fazla

₹555 INR / saat
(0 Değerlendirme)
0.0
FernandoAGV

Hi, Could you fix the problem? I would like to help you with it. I am Senior Electronic Engineer with experience in the design of embedded systems in real time implemented with DSP, FPGA and Microcontrollers. In m Daha Fazla

₹700 INR / saat
(0 Değerlendirme)
0.0
sanuzr

I have used both of the I2C devices mentioned. It shoukd not take me much time to figure out the proble. Though the vontroller your using might be different, you can test my libraries for testing and I canvalidate the Daha Fazla

₹666 INR / saat
(0 Değerlendirme)
0.0
jsinghvirdi

Dear i have 16 years experience in Embedded and PCB Designing. as per my experience this is address of I2C issue, go to internet and search for the same if you have same problem than hire me or some one who resolve thi Daha Fazla

₹555 INR / saat
(0 Değerlendirme)
0.0
Swargamteja

I had 4years industrial experience in Embedded systems .... Almost all I2C sensors are interfaced.. Temperature, humidity, Ambient Light and etc...

₹500 INR / saat
(1 Yorum)
0.0
beratberishaa

I will make a example for you in arduino how to code and e schematic how to connect them in arduino .thank you

₹400 INR / saat
(0 Değerlendirme)
0.0
aymos

Hello dear I cheeked the adress of two piece, and it is ok for both. so the problem to connect both is not related to adress. I have to check with you the schematic, and the program. best regards Aymen

₹638 INR / saat
(0 Değerlendirme)
0.0
parthipankanaka

I hold master degree in instrument tech and having about 35 years of expertise in real time embedded hardware and software applications. I am specializing in IOT.

₹638 INR / saat
(0 Değerlendirme)
0.0
maulin79

I have worked all listed components.

₹600 INR / saat
(0 Değerlendirme)
0.0
₹638 INR / saat
(0 Değerlendirme)
0.0
MarkGalon

Hi, I am interested on this project and I want to share my expertise with you in this project. I am an electronics engineer and IT programmer with over 15 years of experience. I do design of embedded systems and inter Daha Fazla

₹550 INR / saat
(0 Değerlendirme)
0.6