Mcc18 i2c eeprom project işler

. PCB Boyutu 19 cm genişlik, 13cm yükseklik 2. ATMEGA 2560 Micro İşlemci Kullanılacak 3. Çift Katlı PCB isteniyor 4. Güç katı 12 V DC giriş 5 V ve 3.3 V luk çıkış beslemleri olacak. 5. I2C üzerinden ekran bağlanacak. Bu yüzden I2C için GND,VCC,SDA,SCL uçları olan header konacak. 6. Işlemcinin RX3 ve TX3 çıkışları bir jumper aracılığıyla wifi module veya gsm module gidecek. Jumper hangi tarafta ise karta o dizilecek ve çalıştırılacaktır. 7. Wifi için "ESP8266F" modülün kart üzerine konması yeterlidir. 8. GSM için QUECTEL M95 Module kullanılacaktır. Bu modul, sim connectorleri, anten konnektörleri ve gerekli componentler dizil...

I'm searching for a proficient Arduino coder, to support in integrating dc motor driver, lcd20x4 with I2c and inductive proximity sensor into my existing project. The primary goal is to control 2 dc motor simultaneously. Key requirements for this role include: * Proficiency in Arduino coding * Vast experience with sensor integration, specifically using inductive proximity sensors * micro controller

...software - I do not want to see the output of lint! This code has been tested on hardware and performs ok. It controls motors, reads switches, encoders and ADC's, and drives eeprom and digipots. I need a final check to capture any errors or issues that may not be known. I do NOT want any style or general commenting recommendations - the review is ONLY TO IDENTIFY serious issues. I do not want speedup suggestions. This is close to production so any changes *need to be necessary* to improve the quality of the code. Skills and experience required: - Proficiency in C++ programming. - Experience in code review, This 1st project is for approx. 5000 lines of code. If successful then more projects will be offered. I would estimate this should take 3-6 hours. Please pr...

...відображалась поточна температура та також можливість встановлювати температуру через джойстик. Треба щоб значення температури регулювалась через PID-регулятор (програмно) для того щоб пристрої охолодження та нагріву змінювали потужність плавно в залежності від поточної температи. Список датчиків та деталей: 1. Датчик вологості та температури DHT11 (Є також bme 280) 2. Датчик газу MQ2 3. LCD1602 з i2c 4. Джойстик для ардуіно 5. Вентилятор 5v або 12v - для охолодження повітря (такий який в ПК встановлюється) 6. Нагрівальний елемент – лампа накалювання (не остаточний вибір) P.S. якщо треба щось ще чи краще використовувати іншу деталь - напишіть

Hi there, I'm looking for an expert in Arduino programming who can develop custom code. I have all the hardware including an Arduino Uno R4, a NEMA 17 stepper motor, an A4988 stepper motor controller, an RC522 RFID antenna, a 1602IIC LCD display, and push buttons. All of these components...steps made by the stepper motor and messages displayed on the LCD display. I understand that for the stepper motor/controller I will need to supply external power, which is fine. If possible, I would like to also somehow be able to see a log of who had "unlocked" the tool. Not sure how this would work but if it is possible please let me know. IF for the LCD display I need to get one of the fancy I2C display adapters to make the wiring work, please inform me and I will get one. ...

I am looking for a...The main aim of this project will be to program the pressure sensor for: - Accurate data collection and processing - Integration with consumer electronics for seamless performance Preferably, you should have: - Proficiency in Embedded C - Experience with piezoresistive pressure sensor interfacing - Good understanding of I2C communication protocol - Prior experience in developing consumer electronics Your role will involve: - Designing and implementing the software for the pressure sensor - Ensuring optimal performance of the sensor in the consumer electronics product - Testing and troubleshooting to ensure the system works effectively If you have these skills and are confident in delivering high-quality work within the specified time frame, please bid...

The project consists of the design of number 2 PCBs. The first PCB named A is a breakout board for Arduino Mega and Giga, with a maximum size of 140x120 mm. The second PCB named B is a small board and it connects to PCB A with a flat cable, the size is not defined. In the PCBs there are JST HX - 2.54 or standard pin connectors, mosfets for power outputs, two A4988 modules to control 2 stepper motors and two DRV8833 modules to control 4 DC motors, there is also a 1W LED controlled by one of mosfets. The motor modules and mosfets must be equipped with jumpers to select the 5 or 12 volt power supply. Not all mosfets need to be controlled by pwm pins. All digital inputs must include a 10k ohm resistor, but with the possibility of excluding it. There are also digital and analog inputs, ...

I'm in need of a professional to assist in C code writing for my PSoC Creator project. The main task will be to handle the dump and write operations to an I2C EEPROM. You can read the document I upload and Ican send you the part of accelerator which I have wrote successfully. The key responsibilities include: - Developing the necessary algorithms for the dump and write operations - Configuring the necessary peripherals to enable communication with the I2C EEPROM - Implementing interrupt handling for efficient operation The ideal freelancer for this project should have: - Previous experience with writing C code for PSoC Creator projects - Proficiency in handling I2C communication - Strong skills in algorithm development and peripheral ...

We're looking for a programmer with experience of the STM8 MCU. We've already created a program that works well, but flash memory is limited to 8KB and we don't have enough space to store our entire program. The current size of the compiled code is 10 KB. We're looking for a programmer capable of compacting our specific code and libraries used. Our current software includes the follow...experience of the STM8 MCU. We've already created a program that works well, but flash memory is limited to 8KB and we don't have enough space to store our entire program. The current size of the compiled code is 10 KB. We're looking for a programmer capable of compacting our specific code and libraries used. Our current software includes the following libraries: - W...

For this project, we're looking to explore the capabilities of ESP32 - Arduino. In particular, we need help from developers who can demonstrate their understanding of this platform through a demo project. Looking for a simple ESP32/Wifi project for color mixing with LED lightbulb. This is a simple demo project to show WiFi connectivity using the ESP32 microporcessor Using ESP32, 64x128 oLed, one button and 3 LEDs, 10K potentiometer, 1602 LCD (non I2C) Dial in R color using potentiometer 0-255 – Press button, show brightness on RED LED Dial in G color using potentiometer 0-255 – Press button, show brightness on GREEN LED Dial in B color using potentiometer 0-255 – Press button, show brightness on BLUE LED Colors will show on indiv...

I am in need of a Python programmer to work on my Raspberry Pi 4B. The tasks will involve controlling GPIO, integrating an I2C LCD display, programming a 4x3 keypad and dual speaker outputs, as well as controlling seven LED diodes. The project is time sensitive and must be completed before end of April 2024. Skills & Experience needed: - Proficient in Python - Practical knowledge of Raspberry Pi 4B - Experience with hardware integration, specifically GPIO Control, I2C LCD Display, and a 4x3 Keypad - Familiarity with creating and managing networking capabilities If you understand these requirements and are confident that you can successfully deliver this project, I encourage you to place a bid. Let's get started!

I am seeking an experienced developer proficient in C language to develop a Library for a STM...should be suitable for a STM32C0 size MCU. Previous experience in embedded systems and GLCD interfacing is a big plus for this project. Efficiency and attention to detail will be highly valued in this job. Other key attributes - - Low memory footprint - Low power consumption - Powered by a CR2032 battery - I2C interface is our preference - Refresh rate is not critical, There are a number of open source libraries available that can be used as references or to build the solution. We are happy for you to approach it this way as long as there are no IP rights infringed. There are some standard screen setups that will be displayed and these will be shared ones the project is...

I am looking for an experienced engineer who can take on firmware development spanning several wireless devices with Wi-Fi 6, Wi-Fi 7, and LTE 5G connectivity. We are looking for Embedded Engineers to join our team. What you will do: Design, develop, and refactor cloud connectivity apps for our CPEs (Customer Premises Equipment). Reproduce, isol...Networking. Experience with an OpenWrt-based build system, preferably QSDK. Ability to read and write simple scripts in common languages such as Bash, Python, etc. Deep understanding of C and C++ programming for a Linux runtime environment. Nice to have: Experience with Quectel or other vendor LTE. Experience with DeviceTree. Experience with Wireless Technologies. Experience with Luci. Experience with I2C, GPIO, PWM. This is an ongoing...

I am looking for a professional who can help me set up a webserver on ESP32 that hosts a configuration page. This configu...webserver on ESP32 that hosts a configuration page. This configuration page will let users adjust network settings (e.g., SSID, password) and device settings (e.g., name, location). The ideal way to access this page is by automatically redirecting users once they connect to the ESP32. Skills and experience needed: - Extensive experience with ESP32 - Proficiency in setting up web servers - Knowledge in EEPROM data storage on ESP32 - Ability to create user-friendly web interfaces - Understanding of IoT devices and configurations Please bid if you have prior experience working with ESP32, and can deliver a robust, user-friendly web configuration interface on t...

...DS1302 Real Time Clock (RTC) using I2C. Your responsibilities are 1. Create an I2C Driver for the PIC16F887 with the following functions ( i2c_master_initialize, i2c_master_read, i2c_master_write, i2c_slave_initialize, i2c_slave_read, i2c_slave_write). 2. Test the I2C driver over proteus between 2 PIC16F887 MCU (a master and a slave). 3. Write a Driver for DS1302 with the following functions ( ds1302_initialize, ds1302_getTime, ds1302_setTime). 4. Test the DS1302 with the PIC16F887 MCU over proteus. I will receive the full project files and the simulation file. I am using MpLab IDE, so if you are going to use any other IDE you will support me while installing it. Send me a video with everything working properly and I will award you the projec...

Description: We are a drone manuf...currently looking for a skilled and experienced Electronics Engineer and PCB Designer who has good knowledge about Jetson boards and STM32 microcontrollers and has a good hand in designing complex 6-layer PCBs. Project Description: We are aiming to build a custom PCB where we want the take the Jetson Orin nano series carrier board and the NXTPX4 Pro Flight Controller and fuse both of them into one PCB with customization for the External connector pins(USB, CSI, JST). We also want to customize and change the connector of the 40pin header on the jetson board to specific JST connectors for I2C, SPI, USRT, etc. Skills required: -Expert in understanding and creating complex schematics -Expert PCB designer -Expreience with Jetson boards -G...

...ideal candidate will have a strong background in developing firmware for embedded systems, particularly with Raspberry Pi and STM32 microcontrollers. As a Firmware Engineer, you will be responsible for designing, implementing, and testing firmware solutions to meet project requirements. Responsibilities: Design and develop firmware for embedded systems using Raspberry Pi and STM32 microcontrollers. Collaborate with hardware engineers to define system architecture and specifications. Implement firmware features to meet project requirements and deadlines. Debug and troubleshoot firmware-related issues throughout the development lifecycle. Perform code reviews and ensure code quality and adherence to coding standards. Work closely with cross-functional teams to integrate fi...

Necesitamos resolver algunos problemas de un prototipo "final" que está funcionando. Se trata de un equipo que genera ozono, a través de descarga en corona. La placa es básicamente un regulador de volate lineal por PWM, que alimenta al módulo generador de ozono (chino). Además tiene un teclado a membrana, 3 leds y un LCD 20x04 con I2C. El equipo presenta ruido eléctrico, se resetea, se traba, se tilda.

I'm looking for an experienced Arduino programmer to help me with a particular task. The primary aim is to write specific pieces of code that integrate an LCD screen and a SIM800L GSM module with my Arduino project. I want you to create a script for Arduino Uno R3 that with a 16x02 LCD screen with I2C bus will put ">/" at the beginning, there will also be three buttons: one in the middle, one on the right and one on the left. The one on the left will not do anything for the moment, the one in the middle will ensure that when you press it once, a "0" will appear right after ">/", if you press it once more, the "0" will be removed " and in its place a "1" will appear, if you press it once more, the "1" ...

Necesito un timbre para un colegio que funcione en base a un Arduino UNO, un display de 16x2 con interface I2C, un reloj de tiempo real RTC3231 el cual estará encargado de guardar la hora, fecha y los timers de cuando sonará la alarma durante cada día, pulsadores UP / DW para programar los días, horas, minutos y también los segundos en que la alarma o timbre sonará. Pulsadores para confirmar la fecha, hora, minutos y segundos de programación. Debe sonar por lo menos en 6 períodos por día (entrada y salida del colegio, en los recreos o breaks, comienzo y termino de cada período de clase). El Arduino debe activar un relé el cual activará un timbre. El Arduino también debe tener una salida para ...

For this project, I need an Arduino programming expert. I've created a prop airsoft bomb initially designed in Autodesk Tinkercad. All files are ready and in working order, but I would like some adjustments made to the programming. The updated code will need to work with a 16x2 LCD screen communicating through I2C. The following changes are needed: Duel button disarm function Opening screen reading clean up the progroam * Display a countdown timer that starts from 00:00:00. This timer should only start when triggered by a button press. * The LCD screen should also show user instructions. The specifics for those instructions will be provided after hiring. Expertise needed: * Proficient in Arduino programming * Experience working with 16x2 LCD screens and I2C...

...(optional) programming languages. - Ability to read and understand electronic schematics. - Be ready to deal with hardware. - Be striving for self-education and self-organization. - Have good English verbal and written skills (B2/Upper-Intermediate). Qualifications: - Embedded Linux - Multithreading/multiprocessing - ESP32 MCU development - Web protocols (MQTT, WebSocket) - Low-level protocols (UART, I2C, USB) - Wireless protocols (BLE) - Cloud services (AWS) - Electronic schematics and PCB design - Hardware bring up and debug If you believe that your skills and expertise align with the requirements of this position, please send us your CV. Additionally, if you have a portfolio or examples of previous work, we would be interested in seeing them. We are eager to assess your qual...

I am looking for a professional freelancer who is familiar with EAGLE because my PCB project was done in it. A minimal redesign on the PCB is needed since the I2C is not working, and it is not possible to perform a Scanner due to poor wiring of the PCB by the previous freelancer. Only professional freelancers should contact me. The new project can also be done in other software like KiCad, Altium, or again in EAGLE. Thank you in advance.

...(optional) programming languages. - Ability to read and understand electronic schematics. - Be ready to deal with hardware. - Be striving for self-education and self-organization. - Have good English verbal and written skills (B2/Upper-Intermediate). Qualifications - Embedded Linux - Multithreading/multiprocessing - ESP32 MCU development - Web protocols (MQTT, WebSocket) - Low-level protocols (UART, I2C, USB) - Wireless protocols (BLE) - Cloud services (AWS) - Electronic schematics and PCB design - Hardware bring up and debug If you believe that your skills and expertise align with the requirements of this position, please send us your CV for review. Additionally, if you have a portfolio or examples of previous work, we would be interested in seeing them. We are eager to assess...

I require an experienced Embedded Software Engineer to construct an i2c driver to be utilized with the PIC16F887 MCU for communication with the RTC DS1302. Your responsibilities: - Initialize the i2c communication. - Implement the function to read data from the RTC DS1302. - Implement the function to write data to the RTC DS1302. - Simulate the functions over proteus. Skills and Experience Required: - Embedded software development - Familiarity with the PIC16F887 MCU - In-depth knowledge of RTC DS1302 - Proven experience with i2c drivers and RTC I necessitate this project to be completed as swiftly as possible, therefore the ability to adhere to tight deadlines is crucial.

Hi Muhammad T., I noticed your profile and would like to offer you my project. We can discuss any details over chat.

The project uses: I2C GPIO Expander (I2C Address 0x30) ESP32-CAM I2C ADC Rain Sensor Gear Motor Driver (VNH7070AS) The PCB schematic is written in EAGLE

...same router), like UPnP or even better a custom method, possibly simple but reliable. 3. All the clients that have sent a message to the server should be registered in a simple IP list. Then every message from one client should be automatically re-sent over Wi-Fi/UDP to all registered IP-s. 4. Additionally the component should implement low-level basic RX and TX interfacing over one UART and one I2C port. 5. The target HW environment will be Raspberry Pi Zero 2W with Linux. The sending and receiving code should execute possibly in the background in order to allow to use the host Linux platform to perform other processing in parallel. 6. The component should be 2-way and use simple circular queues to buffer RX and TX messages. I have attached a draft, base class Qued with a ...

I'm currently working on a robotics mechatronics project and need a PCB designer specializing in KiCad software. You'll primarily be assisting me with: - Designing a PCB to provide a power supply for an existing general-purpose board based on the STM32H7 series. - Designing a PCB to read 4 AMS AS5047B rotary position sensors alongside 4 limit switches - Designing a PCB to control 4 BLDC motors with PWM Channel with Direction pins - Extracting an I2C port from the assembled PCB Your prior experience in these tasks would be a great advantage. A deep understanding of KiCad design software and STM32H7 series microcontrollers is a must for this project. Assist me in making my robotics mechatronics system dream come true!

...existing PIC24 boards. The scope of work includes: Hardware updates: - Addition of new interfaces - Implementation of new readers like RFID, Weight and other sensors on UART, SPI, I2C Firmware Changes: - Integration of the new reader interfaces - Implementation of bug fixes - Updating existing firmware to accommodate the new changes - Fulfillment of new requirements, which will vary based on specific projects The ideal candidate should have relevant experience in board-level design and firmware engineering, with proficiency in UART, SPI, I2C protocols and development using the PIC24 platform. The project may also involve creating support for additional sensors, enhancing communication capabilities and improving power management, again depending on the speci...

As someone embarking on a project involving the PIC16F887 microcontroller, I'm seeking a highly competent developer to create a specific I2C driver for me. The main purpose of this driver is to support effective communication between PIC16F887 and other I2C compatible devices. Here are the key functionalities the driver should exhibit: - Strengthen the connection between PIC16F887 and DS1302 Real Time Clock (RTC). The right expert for this task would ideally have: - Extensive knowledge of microcontroller development boards - Strong background with PIC16F887 - Proven experience in creating I2C drivers - Detailed understanding of DS1302 RTC If you have these skills and experience and the enthusiasm to embark on this project, please bid!

...registered in a simple IP list. Then every message from one client should be automatically re-sent over Wi-Fi/UDP to all registered IP-s. There is no need to confirm the messages in either way. Consequently it seems that UDP is the right protocol to be used (to be confirmed by the contractor). Additionally the component should implement low-level basic RX and TX interfacing over one UART and one I2C port. The target HW environment will be Raspberry Pi Zero 2W with Linux. The sending and receiving code should execute possibly in the background in order to allow to use the host Linux platform to perform other processing in parallel. The component should be 2-way and use simple circular queues to buffer RX and TX messages. I have attached a draft, base class Qued with a very s...

I am looking for a seasoned professional who can develop a BLDC (Brushless DC) motor control system for my industrial automation project. Requirements: * Experience in BLDC motor controls is essential. * Must be proficient in serial communication systems, particularly UART, SPI, and I2C. * Knowledge of optical encoders is paramount as this will be our preferred feedback mechanism. * Past experience in industrial automation projects will be highly beneficial. * Familiarity with safety and regulatory standards in the industrial automation sector is an added advantage. By the completion of this project, the BLDC motor control should work seamlessly with the rest of our system, supporting effective and efficient operation of our industrial processes.

...micro-controller signals and digital protocols. Key Responsibilities: - Design and create an analyzer able to decipher multiple digital protocols including CAN, SPI, I2C, UART, RS422, RS485, i2C 1-Wire, and SIM devices. - Equip the analyzer with a unique functionality to understand and interpret data in custom HEX, Bianry and ASCII formats. Ideal Experience and Skills: - Proficient in digital protocols and encoding. - Extensive experience in electronics, especially in creating and debugging logic analyzers. - Ability to work with various FPGA's and micro-controller signals. - Strong knowledge of Data formats. This project will be highly suitable for those who have experience in electronics and Verilog software, Cand C# or C++ for the interface GUI preferabl...

...development,  Should have sound knowledge of communication protocol like Rs232,RS485,SPI,I2C,USB & Ethernet and having experience in integration of various hardware system available in our organization and these hardware have RS232 and USB ports and the requirement is to capture the data from these ports and parsed the required data and then store it on the given server. The user must be expert in fetching data from the mentioned ports and ability to develop mobile app for this particular activity will be an added advantage.  Key Project Elements: - The fetching of data from the RS232 and USB ports and store it on the server. - Additional communication modules may be required at later stages of the project. Details will be provided as they become per...

Project Title: Development of Embedded System for Automated Vending Machine Project Overview: I am looking for a skilled freelancer to develop a small embedded system for an automated vending machine. The system should be capable of handling money received from coin, QR code, or RFID, activating a motor accordingly, and displaying live stock on a display or webpage. Functional Requirements: Money Handling: The system should accept money through coin, QR code, or RFID. Motor Control: It should activate a motor based on the money received. Display: The system should display live stock either on a display or a webpage. User Settings: 1. Buttons should be included for setting the price of the product (including the option for a free price), 2. selecting the number of mo...

...“server” one. The main communication between the client and server components should take place in Wi-Fi (typical local single router) network over the TCP/IP or UDP (as recommended by the contractor). The server component will handle additionally some I2C and UART 2-way interfacing. The components should work in the following OS-s: • Client: a multiplatform one, at least Android, Linux and Windows environments, optionally in iOS if including iOS into in a common multiplatform project is possible without a significant increase in the dev project complexity and cost • Server: Linux only Test HW platforms: • The target Linux environment will be Raspberry Pi Zero 2W • Android: tests are planned to be performed on Samsung Galaxy J3 a...

Hey, I am looking for someone who will Design Hardware for ESP32 (Lighting with WS2815). I will do software by myself 1. Power Supply - Battery-operated - 2x18650 batteries connected in series - Ability to be p...2x18650 batteries connected in series - Ability to be powered by 12v (mains adapter) 2. StepUp to 12v for powering the programmable WS2815 LED strip (unless someone convinces me that it's better to use WS2813 with StepDown) - Power consumption for the LED strip, at least 50W, max ~200W - Logic level converter required from 3.3v -> 5v 3. StepDown for powering the ESP32 4. OLED display 128x64 I2C 5. Measurement of power supply voltage and power consumption 6. Power activation via a mechanical switch 7. 2x rotary encoder with button 8. Connector for pro...

I have Raspberry Pi 4 and I2C device connected to Raspberry. Also I have a ubuntu server at AWS. There is an application working on AWS server. It try to read data from i2c bus (ecc://i2c-1). This program try to find i2c-1 bus under "/dev". I want to reach i2c-1 on Remote Raspberry. You can use Remote GPIO on raspberry pi or you can use any other application. Only i need, my application on server should communicate /dev/i2c-1 device (This could be remote raspberry i2c device)

Hey all I am just looking for a simple layout that will allow me to determine when both devices have been connected to the usb...detection. I'm needing it to know if both ends are connected and not just 1 end of the cable. I have attached an image of my KiCad schematic of what I currently have using the INA219. However, it may be better to use a FUSB302/HUSB238 that's designed to monitor both CC pins so that it dont have to use 2 INA219's for each of my 6 usb-c input/output connectors. I plan on using a Arduino Pro Micro for the i2c communication to the FUSB302. I will be needing only 1 passthrough example that I can turn into the 6 input/outputs that I am needing. As always, If you have a better way of doing this then I would like to hear about that way as well as...

I am searching for a programmer specialized with STM32 to develop an inverter. Here are the core competencies you need for the project: - Knowledge of basic communication protocols like UART, SPI, I2C. - Ability to handle sensor integration. - STM32 programming experience, preferred language not specified. - In-depth knowledge in developing off-grid inverters would be a great plus. For this task, you will focus mainly on creating the inverter. The work may require employing a variety of communication protocols and integrating them with various sensors. Please confirm if you have these capabilities before bidding on the project.

...support the I2C interface for data retrieval and control. Function Description The device should possess the following functions: Connection to payment devices through the MDB Master interfaceConnection to vending equipment through the MDB Slave interfaceInteracting with vending equipment through the MDB Slave interface to receive and send commands and messagesData retrieval and control through the I2C interface Requirements for MDB Master The MDB Master module should support the MDB protocol version 4.0 or MDB Master module should support the power-up protocol behavior for the MDB MDB Master module should correctly process messages provided by the MDB protocol and operating modes should be configured through I2C and saved in EEPROM. Requirements

Proof of concept to be scaled in future for Raspi communicating with multiple Arduino devices via I2C bus

Proof of concept to be scaled in future for Raspi communicating with multiple Arduino devices via I2C bus

As a robotic enthusiast, I am seeking...into robot odometry, crucial for robust control systems. Key Functions: - Ros2 foxy - encoders communicate via i2c - Utilize this data, publish it on a topic within the ROS2 ecosystem for further processing. Required Skills and Experience: - Proficiency with ROS2 platform development is mandatory. - Experience with encoder data collection and interpretation. - Understanding of robotics odometry will be advantageous. - Background in autonomous robotics is a significant plus. Pm for more details I have more information if needed As deeply involved as I am in the robotics niche, I am looking to work with someone who is as passionate about robotics as I am. I need this project to begin and complete ASAP. Let's create something e...

...**Firmware Optimization**: Optimize the current firmware, enhancing its performance and efficiency. - **Troubleshooting**: Diagnose and fix bugs in the existing firmware to ensure reliability. - **Communication Mastery**: Implement robust communication protocols such as UART, SPI, and I2C for seamless data exchange with external computers or servers. **Skills Required**: - Advanced knowledge of PiC microcontrollers. - Mastery in Mikrobasic IDE for firmware development. - Proven experience with UART, SPI, I2C protocols. - Ability to integrate multiple functionalities into cohesive firmware. - Capable of interpreting and adhering to hardware specifications. - Previous work with external computers/servers communication. The ideal freelancer should have a track record of suc...

I'm seeking skilled freelancers to bring up the iMax6 SOC Linux and develop a test application. This task will include: 1. Li...develop a test application. This task will include: 1. Linux Deployment: You'll need to deploy Debian on the iMax6 SOC. Experience with SOC Linux configurations, especially with Debian, is crucial. Yocto also OK 2. Test Application Development: You'll develop an application allowing for: - I2C Communication - SPI Communication - GPIO Control - CAN Communication Prior knowledge in these specific types of communication and control is required. Note: The end-users for this project haven't been determined yet. However, a user-friendly and intuitive design could be beneficial for possible end consumers or syst...

PIC16F18313 BASIC Programming and I2C Functionality if you think you are an expert in this type of requirement, kindly place a bid, and lets discuss extensively on project and timeline for delivery

PIC16F18313 BASIC Programming and I2C Functionality if you think you are an expert in this type of requirement, kindly place a bid, and lets discuss extensively on project and timeline for delivery