Ammeter schematic işler

Hello, I need schematic and code for Arduino automatically mix the water from a buffer. I have: - Arduino Uno R compatible board - 2 X DS18B20 temperature sensor - KY-019 Relay - 240 V Water pump I want that the pump will automatically start when the temperature difference from the upper sensor and lower sensor is greater than 10 degree Celsius and stop when the difference is lower than 10 Degree Celsius. I need schematic and code. Thank you!

Hi, I am looking for a 3 phase induction motor controller with following specifications: Input: 96volts DC through LFP battery Output to Motor: 5.5kw, 50Hz, 3 phase 100 volt induction motor in delta connection, Poles:4, Controller sh...50Hz, 3 phase 100 volt induction motor in delta connection, Poles:4, Controller should have circuit breakers for over temperature (motor + controller), over and under voltage and over current/current limitation Forward/Reverse control Speed control On/Off control Motor will start on load and load is dynamic Regenerative braking LCD Display for Speed, Battery, Temp etc. Note: I will need Schematic, PCB design (Gerber file & BoM) and code for the above project. I will also need a working prototype (payable by me) for the project to conclu...

Hello, I need this schematic from web converted to altium project. This is the complete project So i need this schematic and PCB converted to altium using only build in libraries. Task is really simple and there are only 22 components to route. IMPORTANT: I need this done in next 2-3 hours and this is most important. Thank you

I have altium schematic and i need to convert it to PCB and i need one small PCB updated. Schematic is under 100 components and its based around stm32f407. I would like someone who can start working on this project immediately. When applying please include words "I love electronic" so i know you at least read this.

...detection using modulated IR signal. Description can be found in the attached file. Basically it is a simple code if you are a skillful one in PIC Microcontroller. I am using PIC Microcontroller (microchip) only, thus do NOT offer me code for ATmega, PLC, Arduino, Raspberry Pi, etc. I have the current working PCB where I don't plan to modify any single circuit of it. You can ONLY stick to the schematic which I'll provide once I think that you are the right candidate. To prove that you able to do it, please send me the code in mikroC/mikroBasic/PICBASIC or the hex code when I contact you through chat. Once again, do NOT simple bid for the project if you are not planning to send me the test-skills code as it's wasting my time and your time for such conversation whi...

Due to the complex energy nature of the building, accurate prediction of electrical power production, building type and occupancy are essential in building energy management. To help reduce ...can apply three machine learning-based multi-objective prediction frameworks for simultaneous prediction of three optimisation problems on building type, occupancy, and power usage. Since building type, occupancy and power usage share similar affecting factors, it is computational time saving to adopt a multi-objective prediction framework to predict multiple building energy usage features. The schematic diagram of the three proposed predictive models is presented in Fig. 1. In each predictive model, ANN, SVM or LSTM algorithm is adopted. We need a programmer to write code based on our model ...

I need two jacket structure to be analyzed to be analyzed preferably in ANSYS. We want to determine the sturdiness of the structure when subject to weight of a platform on top of the structure, water waves and current, wind load and moment. The attached image shows a schematic of how the loads on the jacket are applied.

I am building a single family home in the city of riverside and I am using a propane tank for my gas delivery. I need a piping schematic design from my tank to the house. About 25 feet Has to comply to the california plumbing code. It's for the city of riverside

We need to complete a Electronic PCB route. The schematic design is finished, but the routing is started but not finished. It is a 120x65 mm PCB, 4 layers.

I need a basic mppt designed in Altium designer with atleast three schematic sheets and basic pcb design for solar cells

Part Time - Amend or draw new M&E drawing in autocad - drawining include schematic, floor plan etc

...information and dimensions on the other components that are relevant including the headlights, swappable batteries, motor, flywheel, shaft, and motor controller. The finished design should behave something like a cardboard fold-able that we can stencil or sketch onto a large sheet of metal and then cut and bend to create the 3d shape. The whole design does not need fit into a single foldable schematic but we want to keep the total number of compartments to a minimum, ideally less than 5. It could be one compartment entirely which encompasses all components or it can be multiple as in one for the motor block, one for the battery box, one for the front headlamp and grill assembly and one for the control display. Ultimately we are looking for functional design ideas that take a lit...

Looking for an HTML designer to design a website that includes about 6 pages (Home, Search, 2 Product Pages, Shopping Cart, Purchase) There is a schematic design that required the creation of HTM and FRONT-END pages We will not press BACK-END

Dear bidder, I want to build a small CNC-Project and need an arduino sketch as well as recommendation about the parts I need. As I am not very used to arduino I also need some assist in adding the library and connecting all together. Parts I want to use: Arduino with CNC-shield, two Nema Stepper and 3 Endstops. LCD-Display (16x2) with 6-Button control. 240V device controlled by SSR. Function: Arduino controls the Stepper after Input Values and start process: 1. Enable SSR 2. Move stepper X in +direction until endstop1 3. Disable SSR 4. Pause x-seconds on endstop1 5. Move stepper X in –direction until endstop2 6. Move stepper-y in +direction for x-mm 7. Enable SSR 8. Repeat step 1. – 7. Until stepper-y hits endstop3 9. End LCD-controll: When bootup or reset Arduino: 1. Y-feed...

Eu preciso de você para desenvolver um software para mim. Gostaria que este software fosse desenvolvido.

Use my existing 2D AutoCAD drawings to revise details to make the drawings specific for a project. Mainly requires manipulating the drawing text. Changing some minor line drawings to indicate the plumbing schematic. Each drawing has the DWG file to work from and a PDF file with the changes required noted. 3 fountains in total.

I am looking for a quick shematic to accommodate ESP8266 with logical level shift and be able to communicate Programmable LED's, Preferably ws2812B. Programming is not required if you think it's too much. we can take care of programming. Please take a look at the attachment which consist of detailed description and please feel free to reach out to me.

Need PCB design/layout for a power supply. Schematic and basic mechanicals provided. Schematic design is in OrCAD. Can output to another net list format as required. No preference for any particular layout software.

I have a schematic that needs an update and converted to PCB and the output needs to be a gerber file suitable for sending out to be made. I am open to suggestions for both the power input (+12v) and the motor output regarding connectors. I did not build in (but needs it), protection from reverse power on the 12v.

I would like to show you a schematic of a radio (rf) project that I would like a pcb designed for and advise and help on which components to use and how to replicate the project. Thankyou!

Build webpage, use information from when new page is done it should replace the old one. but both should work at same time, new one should not be crawled by google. Schematic in faq, bredcrumb and blog is important, you want me to buy Divi Schema Plugin?

We need electrical control Panel power distribution diagram/schematic sheets and wiring detail with BOM. A freelancer who knows EPlan software working can do this.

Hello, I need someone to design a simple one layer PCB for an Arduino project. I have attached some drawings and a simple schematic. I just basically need someone to draw it up in a PCB design software so I can send it out to be manufactured. The components can be shifted around as long as the board stays at 83.5mm x 83.5mm. The 2x resistors will be 1/8 watt resistors.

Hello, I need someone to design a simple one layer PCB for an Arduino project. I have attached some drawings and a simple schematic. I just basically need someone to draw it up in a PCB design software so I can send it out to be manufactured. The components can be shifted around as long as the board stays at 83.5mm x 83.5mm. The 2x resistors will be 1/8 watt resistors.

I need to reproduce the schematic first and then the pcb that is no longer manufactured i only have the photo of the pcb that like to copy its a pcb to control a 1-axis Brushless Gimbal, with imu invensense mpu.6050, usb to uart bridge, microchip atmega328p-mu to work with simpleBGC firmwares. No shmatic avaliable

Looking for anyone who can help in my project to create my first prototype with following Our d...buttons all the settings has to be changed to default settings All the buttons other than simulation buttons must function as provided in the video below which shows real depress time as we hold any button for its respective purpose The mouse sensor I would like to use in RHS is Pixart ADNS-3050 I would like to work by following milestones: Hardware Design is divided into 3 milestones (Schematic + PCB layout + Gerber & BOM) to manufacture the Prototype 4th Milestone would be Firmware Coding(MCU code where will be used in the project) 5th Milestone: Prototyping and Testing(make the prototype and test the prototype with the firmware code) + Shipment of a working prototype i...

Hello Developer Looking for an electronic Engineer who can design 8 Port Gigabit Unmanaged Switch Schematic. for further discuss you can request to chat with me.

I need a Relay Board PCB design for fan speed control. It involves 4 relays (5 pin) and 3 CBB capacitors. I am attaching the reference schematic.

This is for an electronic pet door. Consumer quality product. Need to have our existing PCB redesigned. Previously we depended on "full service" mfrs, who retain the PCB design files. We would like to regain control of the design, so that we can send out for board mfg bid. And make chan...have our existing PCB redesigned. Previously we depended on "full service" mfrs, who retain the PCB design files. We would like to regain control of the design, so that we can send out for board mfg bid. And make changes readily. The board is mostly surface mount, with 7 ICs, a small power transformer and the usual discrete components. Double sided. Dimensions 2" by 5". I am the EE and have schematic and detailed knowledge. DXesigner would have a sample of existing b...

I give the altium schematic file. You have to modify the canbus / rs-232 selector jumper, add a circuit for external dht22 and mpu6050 / 9250. then make the pcb with the specified dimensions and shape.

Experienced Electrical Engineer able to audit a 3rd party job (freelancer hired by this platform). The Auditor will analyze and determine if the output provided by Designer Electrical Engineer is good for the goals of the project (add and additional Ethernet output port and provide us the schematic and pcb design layout files). The Auditor needs to be independent about the Electrical Designer and provide us with Auditing Advice about the good quality of the performed job. More infomation will be provided thru Chat for those interested on the project.

...buttons all the settings has to be changed to default settings All the buttons other than simulation buttons must function as provided in the video below which shows real depress time as we hold any button for its respective purpose The mouse sensor I would like to use in RHS is Pixart ADNS-3050 I would like to work by following milestones: Hardware Design is divided into 3 milestones (Schematic + PCB layout + Gerber & BOM) to manufacture the Prototype 4th Milestone would be Firmware Coding(MCU code where will be used in the project) 5th Milestone: Prototyping and Testing(make the prototype and test the prototype with the firmware code) + Shipment of a working prototype in 3D enclosure ...

See the attached documents. I have the schematic and a system overview. I will be using an Arduino nano with the old bootloader style board.

...after pressing the following buttons all the settings has to be changed to default settings All the buttons other than simulation buttons must function as provided in the video below which shows real depress time as we hold any button for its respective purpose The mouse sensor I would like to use in RHS is Pixart ADNS-3050 I would like to work by following milestones: 1. Hardware Design(Schematic + PCB layout + Gerber + BOM) to manufacture the Prototype 2. Firmware Coding(MCU code where will be used in the project) 3. Prototyping and Testing(make the prototype and test the prototype with the firmware code )...

Looking for an HTML designer to design a website that includes about 6 pages (Home, Search, 2 Product Pages, Shopping Cart, Purchase) There is a schematic design that required the creation of HTM and FRONT-END pages We will not press BACK-END

Lütfen detayları görmek için Kaydolun ya da Giriş Yapın.

I HAVE A FLOW DIAGRAM THAT I WANT TO DEMONSTRATE TO MY CLIENT. This is what I want, as follows: 4 pages 1. Moving graphics (color) in the back ground and some light music. 2. flow schematic chart -re-designed into a bigger format. 3. scrolling text, real automated voice, in each box COLOR FILL as it appears. 4. as the box is read, then it appears then needs to be colored in the box. After the highlight we move along to the next flow chart (while leaving the box we just did highlighted/colored). Next box led by a highlighted line. This continues for each box WITH ARROWS AND LINES FOR EACH NUMBERED BOX. Perhaps some definitions or explanations after some boxes. 5. The flow chart design will be that each time we come to a box the client can follow the line to the next box i...

Hi I need to design a schematic for the power supply in Eagle. Hot swapped battery concept. Cannot pay more than the budget. I need all the libraries and all the components should be properly labeled. Let's talk.

We are developing embedded product for segment and looking for competitive technical resources(Individual or team) for the below pr...for competitive technical resources(Individual or team) for the below provided activities parts with right source and compliant to design standards and manufacturability embedded firmware and necessary scripts for ARM based micro controller (STM32 series) to control and monitor the device/equipment and also different kind of sensors ,Camera module and Wifi sections schematic and design PCB as per the requirement. Android based app for Tab/mobile to provide real time video interface and control and diagnostics feature for the end product. final integration and testing as necessary Ram Director UnimechAerospace

I need schematics and a PCB with a ESP-WROOM-32, a USB to serial chip (CH340C), and voltage regulator (RT9080-33GJ5). Additionally, I need the board to have specifically space through holes for a PIR sensor, with a resistor between the data and ground. I also will need through holes for soldering battery wires. I am more than happy to describe our needs more clearly as well as provide a PDF copy of the schematics for the development board that I have been using thus far.

Need to make calculations and illustrations for the given requirement Requirement Consider that XYZ company plan to deploy Wide Area Network (WAN) core optical network infrastructure and Cloud Services (Data Centres) in which organization operation are throughout the branches. Table 1 shown the Nodes and Data Centres for company with data rates of 40Gbps is bei...Recommend and deduce an appropriate CIDR addressing scheme. 4. Evaluate the maximum length of the optical link from ingress to egress, assuming that there are no amplifiers. 5. If the link operates at a rate of 230 Gbps and an average dispersion limit of 1400 Gbpskm. Rate the maximum length of the optical links from ingress to egress. 6. Recommend and illustrate the Optical Cross-Connect (OXC) schematic structure....

Need to make calculations and illustrations for the given requirement Requirement Consider that XYZ company plan to deploy Wide Area Network (WAN) core optical network infrastructure and Cloud Services (Data Centres) in which organization operation are throughout the branches. Table 1 shown the Nodes and Data Centres for company with data rates of 40Gbps is being setup f...Recommend and deduce an appropriate CIDR addressing scheme. 4. Evaluate the maximum length of the optical link from ingress to egress, assuming that there are no amplifiers. 5. If the link operates at a rate of 230 Gbps and an average dispersion limit of 1400 Gbpskm. Rate the maximum length of the optical links from ingress to egress. 6. Recommend and illustrate the Optical Cross-Connect (OXC) schematic ...

Looking for consultant to assist with a reverse engineering project that involves testing and measuring high voltage dc discharges and quantifying/ qualifying subsequent PCB health feedback pulse train signals. Deliverables include a " functional report" of a diagnostic pcb, cost effective test equipment plan/ bill of material and complete reverse engineering schematic of the diagnostic pcb.

...time. Design files are checked-in to repository, Test reports are prepared and reviewed, Defects are updated in Jira - Engineering Samples Protos Support - Hardware boards bring-up, building proto units, HW and System verification testing for supported configurations - Update sensor boards designs (Altium designer) based on inputs from testing, various reviews and release updated design files (schematic, BOM, gerber, layout etc.) - Eval Units for pilot deployments - Hardware boards bring-up, building eval units, HW and System testing for supported configurations including battery powered operations of sensor units - German Language (at least B2) - German working permit is mandatory - working onsite at the costumer is a must!!! Please send me your CV in WORD format and your ho...

We have an environmental monitoring system which uses an ESP32 controller. It uses i2c protocol to talk to sensors, which is not working reliably enough in a noisy environment, so we'd like to change to RS485/MODBUS. We already have the RS485 sensors. This project is to update our main board schematic and PCB for RS485, as well as updating the firmware to use the new sensors.

We are looking for an electronic engineer to Design an electronic filter to pass only 2 frequency 130Khz and 190Khz. We need only schematic and BOM. Not need it PCB design

i want power supply design for 230VAC to 3VDC. I need schematic and PCB design both. Please do not do copy paste from other websites.

I am looking for somebody who can build a Shopify website based on specifications and design inspirations that we will provide you in detail. We have the schematic and the design we're looking for somebody that can build it with the apps and plugins successfully. Please message me I will share the details with you - then proceed to send me a quotation and a timescale for completion.

Need to layout a PCB for gang charging 5v devices ( 10 devices) including a 10 port USB hub. The schematic will be provided, the size is approximately 86x 180 mm

I have a board that connects an Arduino Nano to a memory IC (AT25SL321). I need a code to - Read and write audio files to the memory IC - Provide the ability to copy audio files from SD card to memory IC I can provide the schematic